= Capturing Console Log = Console log: Copy and Paste of the serial console activity from a Gateworks Board. This is very helpful to allow Gateworks to help customers debug issues. Console log should include: 1. Complete console activity from power on (start with board powered off, setup serial console , then power the board) - This will show the serial console with the U-Boot information 2. The final command prompt once the board has completely finished booting 3. Any errors, etc encountered thereafter. '''For Example,''' ''' This example is very long but please note the following mandatory parameters:''' 1. The first line shows U-Boot 2. The OpenWrt Banner (very bottom) 3. The last line shows root@OpenWrt {{{ U-Boot 2013.07-00012-g88e0a40 (Sep 25 2013 - 13:36:02) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR APP_IMAGE: Primary Env: SPI FLASH BOOT_CFG: SPI NOR 0x18000030 Gateworks Corporation Copyright 2013 Model: GW5400-A MFGDate: 04-29-2013 Serial:504743 DRAM: 1 GiB PMIC: deviceid=10, revid=11 GSC: v2 0x8a31 0x00 RTC: 0 MMC: FSL_SDHC: 0 SF: Detected W25Q256 with page size 64 KiB, total 32 MiB No panel detected: default to HDMI enable_hdmi: setup HDMI monitor DISP: HDMI (1024x768) In: serial Out: serial Err: serial RS232: enabled DIO0: gpio DIO1: gpio DIO2: gpio DIO3: gpio Net: FEC [PRIME] Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found USB device 0: unknown device ** Bad device usb 0 ** MMC: no card present mmc0(part 0) is current device MMC: no card present MMC: no card present ** Bad device mmc 0 ** SF: Detected W25Q256 with page size 64 KiB, total 32 MiB SF: 2097152 bytes @ 0x90000 Read: OK Booting from FLASH... ## Loading kernel from FIT Image at 12000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: Linux Kernel OpenWrt Linux-3.8.3 Type: Kernel Image Compression: uncompressed Data Start: 0x120000e8 Data Size: 1644616 Bytes = 1.6 MiB Architecture: ARM OS: Linux Load Address: 0x10008000 Entry Point: 0x10008000 Hash algo: crc32 Hash value: 80fbc04b Hash algo: sha1 Hash value: 41eb2ce27e1e5f2649edce77f673f1e5813bfd4c Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 12000000 ... Using 'config@1' configuration Trying 'fdt@1' fdt subimage Description: Flattened Device Tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x12191a58 Data Size: 23080 Bytes = 22.5 KiB Architecture: ARM Hash algo: crc32 Hash value: 271d3e89 Hash algo: sha1 Hash value: b20b952d8ebefe82412e40dad1a647caa2a841d1 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x12191a58 Loading Kernel Image ... OK Using Device Tree in place at 12191a58, end 1219a47f Updating MTD partitions... Adjusting FDT per EEPROM for gw5400-a... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.8.3 (tharvey@tharvey-desktop) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #3 SMP Tue Apr 9 10:47:30 PDT 2013 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Freescale i.MX6 Quad (Device Tree), model: Gateworks Ventana GW5400 [ 0.000000] Truncating RAM at 10000000-4fffffff to -3f7fffff (vmalloc region overlap). [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] PERCPU: Embedded 7 pages/cpu @c0abb000 s6336 r8192 d14144 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 193040 [ 0.000000] Kernel command line: console=ttymxc1,115200 root=/dev/mtdblock3 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Memory: 760MB = 760MB total [ 0.000000] Memory: 766308k/766308k available, 11932k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0431e24 (4264 kB) [ 0.000000] .init : 0xc0432000 - 0xc04668c0 ( 211 kB) [ 0.000000] .data : 0xc0468000 - 0xc048b5fc ( 142 kB) [ 0.000000] .bss : 0xc048b5fc - 0xc04ba38c ( 188 kB) [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x000000c0, AUX_CTRL 0x02070000, Cache size: 1048576 B [ 0.000000] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 65075ms [ 0.000000] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.000198] Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280) [ 0.090124] pid_max: default: 32768 minimum: 301 [ 0.090284] Mount-cache hash table entries: 512 [ 0.094900] CPU: Testing write buffer coherency: ok [ 0.095140] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.095233] Setting up static identity map for 0x10010bf0 - 0x10010c24 [ 0.096531] CPU1: Booted secondary processor [ 0.185195] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.185937] CPU2: Booted secondary processor [ 0.225196] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.225940] CPU3: Booted secondary processor [ 0.265194] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.265238] Brought up 4 CPUs [ 0.265270] SMP: Total of 4 processors activated (6324.22 BogoMIPS). [ 0.265967] pinctrl core: initialized pinctrl subsystem [ 0.266618] regulator-dummy: no parameters [ 0.267054] NET: Registered protocol family 16 [ 0.269221] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.269696] pwm_init [ 0.280310] syscon 20c8000.anatop: syscon regmap start 0x20c8000 end 0x20c8fff registered [ 0.280658] vdd1p1: 800 <--> 1375 mV at 1100 mV [ 0.281044] vdd3p0: 2800 <--> 3150 mV at 3000 mV [ 0.281457] vdd2p5: 2000 <--> 2750 mV at 2400 mV [ 0.281852] cpu: 725 <--> 1450 mV at 1150 mV [ 0.282241] vddpu: 725 <--> 1450 mV at 1150 mV [ 0.282648] vddsoc: 725 <--> 1450 mV at 1200 mV [ 0.284192] syscon 20e0000.iomuxc-gpr: syscon regmap start 0x20e0000 end 0x20e0037 registered [ 0.289469] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.303320] bio: create slab at 0 [ 0.306766] mxs-dma 110000.dma-apbh: initialized [ 0.307482] 2P5V: 2500 mV [ 0.307746] 3P3V: 3300 mV [ 0.307990] usb_otg_vbus: 5000 mV [ 0.309008] SCSI subsystem initialized [ 0.309941] usbcore: registered new interface driver usbfs [ 0.310086] usbcore: registered new interface driver hub [ 0.310259] usbcore: registered new device driver usb [ 0.315962] i2c i2c-0: IMX I2C adapter registered [ 0.317321] i2c i2c-1: IMX I2C adapter registered [ 0.319469] i2c i2c-2: IMX I2C adapter registered [ 0.319619] Linux video capture interface: v2.00 [ 0.319835] pps_core: LinuxPPS API ver. 1 registered [ 0.319847] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.320810] Advanced Linux Sound Architecture Driver Initialized. [ 0.322210] Switching to clocksource mxc_timer1 [ 0.324218] NET: Registered protocol family 2 [ 0.324739] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.324875] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.325022] TCP: Hash tables configured (established 8192 bind 8192) [ 0.325114] TCP: reno registered [ 0.325131] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.325199] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.325557] NET: Registered protocol family 1 [ 0.325856] i.MXC CPU frequency driver [ 0.325871] i.MXC CPU frequency driver [ 0.325881] i.MXC CPU frequency driver [ 0.325891] i.MXC CPU frequency driver [ 0.468460] pcie: IMX PCIe port: link up. [ 0.468707] PCI host bridge to bus 0000:00 [ 0.468730] pci_bus 0000:00: root bus resource [io 0x1000000-0x10fffff] [ 0.468744] pci_bus 0000:00: root bus resource [mem 0x01100000-0x01efffff] [ 0.468758] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.469011] PCI: bus0: Fast back to back transfers disabled [ 0.469026] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.469601] pcie: 1:00.2 0x0000: master abort [ 0.471113] pcie: 1:00.3 0x0000: master abort [ 0.472648] pcie: 1:00.4 0x0000: master abort [ 0.474160] pcie: 1:00.5 0x0000: master abort [ 0.475670] pcie: 1:00.6 0x0000: master abort [ 0.477179] pcie: 1:00.7 0x0000: master abort [ 0.478710] PCI: bus1: Fast back to back transfers disabled [ 0.478727] pci 0000:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.478834] pcie: 2:00.0 0x0000: master abort [ 0.480688] pcie: 2:02.0 0x0000: master abort [ 0.482199] pcie: 2:03.0 0x0000: master abort [ 0.485748] pcie: 2:10.0 0x0000: master abort [ 0.487259] pcie: 2:11.0 0x0000: master abort [ 0.488770] pcie: 2:12.0 0x0000: master abort [ 0.490279] pcie: 2:13.0 0x0000: master abort [ 0.491788] pcie: 2:14.0 0x0000: master abort [ 0.493316] pcie: 2:15.0 0x0000: master abort [ 0.494828] pcie: 2:16.0 0x0000: master abort [ 0.496339] pcie: 2:17.0 0x0000: master abort [ 0.497848] pcie: 2:18.0 0x0000: master abort [ 0.499357] pcie: 2:19.0 0x0000: master abort [ 0.500867] pcie: 2:20.0 0x0000: master abort [ 0.502390] pcie: 2:21.0 0x0000: master abort [ 0.503900] pcie: 2:22.0 0x0000: master abort [ 0.505410] pcie: 2:23.0 0x0000: master abort [ 0.506920] pcie: 2:24.0 0x0000: master abort [ 0.508430] pcie: 2:25.0 0x0000: master abort [ 0.509939] pcie: 2:26.0 0x0000: master abort [ 0.511448] pcie: 2:27.0 0x0000: master abort [ 0.512971] pcie: 2:28.0 0x0000: master abort [ 0.514481] pcie: 2:29.0 0x0000: master abort [ 0.515991] pcie: 2:30.0 0x0000: master abort [ 0.517500] pcie: 2:31.0 0x0000: master abort [ 0.519152] PCI: bus2: Fast back to back transfers disabled [ 0.519168] pci 0000:02:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.519196] pci 0000:02:04.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.519225] pci 0000:02:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.519255] pci 0000:02:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.519283] pci 0000:02:07.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.519310] pci 0000:02:08.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.519337] pci 0000:02:09.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.519503] pcie: 3:00.0 0x0000: master abort [ 0.521011] PCI: bus3: Fast back to back transfers enabled [ 0.521187] pcie: 4:00.0 0x0000: master abort [ 0.522712] PCI: bus4: Fast back to back transfers enabled [ 0.522893] pcie: 5:00.0 0x0000: master abort [ 0.524401] PCI: bus5: Fast back to back transfers enabled [ 0.524573] pcie: 6:00.0 0x0000: master abort [ 0.526082] PCI: bus6: Fast back to back transfers enabled [ 0.526255] pcie: 7:00.0 0x0000: master abort [ 0.527762] PCI: bus7: Fast back to back transfers enabled [ 0.528439] PCI: bus8: Fast back to back transfers disabled [ 0.528614] pcie: 9:00.0 0x0000: master abort [ 0.530123] PCI: bus9: Fast back to back transfers enabled [ 0.534082] pci 0000:00:00.0: BAR 0: assigned [mem 0x01100000-0x011fffff 64bit pref] [ 0.534113] pci 0000:00:00.0: BAR 8: assigned [mem 0x01200000-0x013fffff] [ 0.534127] pci 0000:00:00.0: BAR 6: assigned [mem 0x01400000-0x0140ffff pref] [ 0.534140] pci 0000:00:00.0: BAR 7: assigned [io 0x1000000-0x1000fff] [ 0.534158] pci 0000:01:00.0: BAR 8: assigned [mem 0x01200000-0x012fffff] [ 0.534171] pci 0000:01:00.0: BAR 0: assigned [mem 0x01300000-0x0131ffff] [ 0.534188] pci 0000:01:00.1: BAR 0: assigned [mem 0x01320000-0x0133ffff] [ 0.534204] pci 0000:01:00.0: BAR 7: assigned [io 0x1000000-0x1000fff] [ 0.534223] pci 0000:02:08.0: BAR 8: assigned [mem 0x01200000-0x012fffff] [ 0.534236] pci 0000:02:08.0: BAR 7: assigned [io 0x1000000-0x1000fff] [ 0.534249] pci 0000:02:01.0: PCI bridge to [bus 03] [ 0.534294] pci 0000:02:04.0: PCI bridge to [bus 04] [ 0.534333] pci 0000:02:05.0: PCI bridge to [bus 05] [ 0.534371] pci 0000:02:06.0: PCI bridge to [bus 06] [ 0.534411] pci 0000:02:07.0: PCI bridge to [bus 07] [ 0.534454] pci 0000:08:00.0: BAR 0: assigned [mem 0x01200000-0x01203fff 64bit] [ 0.534495] pci 0000:08:00.0: BAR 2: assigned [io 0x1000000-0x10000ff] [ 0.534513] pci 0000:02:08.0: PCI bridge to [bus 08] [ 0.534529] pci 0000:02:08.0: bridge window [io 0x1000000-0x1000fff] [ 0.534549] pci 0000:02:08.0: bridge window [mem 0x01200000-0x012fffff] [ 0.534579] pci 0000:02:09.0: PCI bridge to [bus 09] [ 0.534618] pci 0000:01:00.0: PCI bridge to [bus 02-09] [ 0.534631] pci 0000:01:00.0: bridge window [io 0x1000000-0x1000fff] [ 0.534648] pci 0000:01:00.0: bridge window [mem 0x01200000-0x012fffff] [ 0.534670] pci 0000:00:00.0: PCI bridge to [bus 01-09] [ 0.534682] pci 0000:00:00.0: bridge window [io 0x1000000-0x1000fff] [ 0.534696] pci 0000:00:00.0: bridge window [mem 0x01200000-0x013fffff] [ 0.534725] PCI: enabling device 0000:01:00.0 (0140 -> 0143) [ 0.534748] PCI: enabling device 0000:02:01.0 (0140 -> 0143) [ 0.534773] PCI: enabling device 0000:02:04.0 (0140 -> 0143) [ 0.534799] PCI: enabling device 0000:02:05.0 (0140 -> 0143) [ 0.534824] PCI: enabling device 0000:02:06.0 (0140 -> 0143) [ 0.534849] PCI: enabling device 0000:02:07.0 (0140 -> 0143) [ 0.534875] PCI: enabling device 0000:02:08.0 (0140 -> 0143) [ 0.534900] PCI: enabling device 0000:02:09.0 (0140 -> 0143) [ 0.546980] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.546998] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.547848] msgmni has been set to 1496 [ 0.548083] io scheduler noop registered [ 0.548096] io scheduler deadline registered [ 0.548137] io scheduler cfq registered (default) [ 0.549129] imx-sdma 20ec000.sdma: loaded firmware 1.1 [ 0.554155] imx-sdma 20ec000.sdma: initialized [ 0.554559] Serial: IMX driver [ 0.555082] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX [ 0.555833] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX [ 1.642660] console [ttymxc1] enabled [ 1.646926] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX [ 1.654387] [drm] Initialized drm 1.1.0 20060810 [ 1.659149] at24 0-0050: 256 byte 24c02 EEPROM, writable, 16 bytes/write [ 1.665919] at24 0-0051: 256 byte 24c02 EEPROM, writable, 16 bytes/write [ 1.672679] at24 0-0052: 256 byte 24c02 EEPROM, writable, 16 bytes/write [ 1.679412] at24 0-0053: 256 byte 24c02 EEPROM, writable, 16 bytes/write [ 1.688656] spi_imx 2008000.ecspi: master is unqueued, this is deprecated [ 1.696036] m25p80 spi32766.0: w25q256 (32768 Kbytes) [ 1.701283] 4 ofpart partitions found on MTD device spi32766.0 [ 1.707159] Creating 4 MTD partitions on "spi32766.0": [ 1.712322] 0x000000000000-0x000000080000 : "uboot" [ 1.718256] 0x000000080000-0x000000090000 : "env" [ 1.723980] 0x000000090000-0x000000290000 : "kernel" [ 1.729911] 0x000000290000-0x000001000000 : "rootfs" [ 1.735887] mtd: partition "rootfs" set to be root filesystem [ 1.741859] mtd: partition "rootfs_data" created automatically, ofs=8D0000, len=730000 [ 1.749905] 0x0000008d0000-0x000001000000 : "rootfs_data" [ 1.756376] spi_imx 2008000.ecspi: probed [ 1.775427] libphy: fec_enet_mii_bus: probed [ 1.780632] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.787197] ehci-pci: EHCI PCI platform driver [ 1.791815] ehci-platform: EHCI generic platform driver [ 1.800574] ci_hdrc ci_hdrc.0: can't start gadget role [ 1.805872] imx_usb 2184200.usb: pinctrl get/select failed, err=-19 [ 1.812526] ci_hdrc ci_hdrc.1: doesn't support gadget [ 1.817594] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 1.822543] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 1.842279] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 1.848257] hub 1-0:1.0: USB hub found [ 1.852030] hub 1-0:1.0: 1 port detected [ 1.856590] input: mma8450 as /devices/virtual/input/input0 [ 1.862750] rtc-ds1672 0-0068: chip found, driver version 0.4 [ 1.869873] rtc-ds1672 0-0068: rtc core: registered rtc-ds1672 as rtc0 [ 1.877356] i2c /dev entries driver [ 1.881901] imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1) [ 1.890463] sdhci: Secure Digital Host Controller Interface driver [ 1.896669] sdhci: Copyright(c) Pierre Ossman [ 1.901033] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.908706] mmc0: no vqmmc regulator found [ 1.952291] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 1.959983] leds-gpio leds.8: pins are not configured from the driver [ 1.968064] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 1.974711] [drm] No driver support for vblank timestamp query. [ 1.980641] [drm] Initialized imx-drm 1.0.0 20120507 on minor 0 [ 1.990912] imx-ipuv3 2400000.ipu: DI0 base: 0x02640000 remapped to f00fe000 [ 1.998120] imx-ipuv3 2400000.ipu: DI1 base: 0x02648000 remapped to f0244000 [ 2.005662] imx-ipuv3 2400000.ipu: IPUv3H probed [ 2.014543] imx-ipuv3 2800000.ipu: DI0 base: 0x02a40000 remapped to f0264000 [ 2.021682] imx-ipuv3 2800000.ipu: DI1 base: 0x02a48000 remapped to f0266000 [ 2.029177] imx-ipuv3 2800000.ipu: IPUv3H probed [ 2.036438] sgtl5000 2-000a: Failed to get supply 'VDDD': -517 [ 2.042583] 2-000a: 1200 mV normal [ 2.046278] sgtl5000 2-000a: Using internal LDO instead of VDDD [ 2.055127] sgtl5000 2-000a: sgtl5000 revision 0x11 [ 2.071211] imx-sgtl5000 sound.13: sgtl5000 <-> 2028000.ssi mapping ok [ 2.079922] TCP: cubic registered [ 2.083343] NET: Registered protocol family 17 [ 2.087923] Bridge firewalling registered [ 2.091948] 8021q: 802.1Q VLAN Support v1.8 [ 2.096250] Registering SWP/SWPB emulation handler [ 2.103445] rtc-ds1672 0-0068: setting system clock to 1970-01-01 00:00:08 UTC (8) [ 2.111060] imx-drm imx-drm: No connectors reported connected with modes [ 2.117793] [drm] Cannot find any crtc or sizes - going 1024x768 [ 2.129631] imx-drm imx-drm: fb0: frame buffer device [ 2.134816] imx-drm imx-drm: registered panic notifier [ 2.146669] ALSA device list: [ 2.149648] #0: imx6q-sabrelite-sgtl5000 [ 2.167097] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 2.172316] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 2.180954] Freeing init memory: 208K [ 2.404364] hub 1-1:1.0: USB hub found [ 2.408460] hub 1-1:1.0: 4 ports detected [ 3.097948] pcie: PCIe abort: address = 0xb6f7d000 fsr = 0x1406 PC = 0xb6f75a48 LR = 0xb6f76578 instr=ef000000 - preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - [ 7.666174] jffs2: notice: (1165) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 12 of xref (0 dead, 0 orphan) found. switching to jffs2 - init - Please press Enter to activate this console. [ 9.267757] Compat-drivers backport release: compat-drivers-2013-01-21-1 [ 9.274493] Backport based on wireless-testing.git master-2013-02-22 [ 9.280850] compat.git: wireless-testing.git [ 9.297707] cfg80211: Calling CRDA to update world regulatory domain [ 9.304178] cfg80211: World regulatory domain updated: [ 9.309336] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 9.317569] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.325337] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 9.333104] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 9.340855] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.348618] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Failed to set regulatory domain: -7 [ 10.617053] RPC: Registered named UNIX socket transport module. [ 10.623011] RPC: Registered udp transport module. [ 10.627719] RPC: Registered tcp transport module. [ 10.632439] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 10.875585] NTFS driver 2.1.30 [Flags: R/O MODULE]. [ 11.239182] PPP generic driver version 2.4.2 [ 11.353666] tun: Universal TUN/TAP device driver, 1.6 [ 11.358732] tun: (C) 1999-2004 Max Krasnyansky [ 11.419915] gre: GRE over IPv4 demultiplexor driver [ 11.433469] ip_gre: GRE over IPv4 tunneling driver [ 11.587444] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 11.742364] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 11.891426] ip_tables: (C) 2000-2006 Netfilter Core Team [ 12.022002] NET: Registered protocol family 24 [ 12.146256] nf_conntrack version 0.5.0 (11976 buckets, 47904 max) [ 12.730875] xt_time: kernel timezone is -0000 [ 12.891681] Ebtables v2.0 registered [ 13.129050] batman_adv: B.A.T.M.A.N. advanced 2013.1.0 (compatibility version 14) loaded [ 13.149246] e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k [ 13.155117] e1000e: Copyright(c) 1999 - 2012 Intel Corporation. [ 13.270863] sky2: driver version 1.30 [ 13.274629] PCI: enabling device 0000:08:00.0 (0140 -> 0143) [ 13.280417] sky2 0000:08:00.0: Yukon-2 UL 2 chip revision 0 [ 13.286357] arch_setup_msi_irq: 0 of 16 [ 13.382291] sky2 0000:08:00.0: No interrupt generated using MSI, switching to INTx mode. [ 13.391006] sky2 0000:08:00.0 eth1: addr 00:d0:12:29:ef:6d [ 13.449598] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 13.513757] uhci_hcd: USB Universal Host Controller Interface driver [ 13.571457] usbcore: registered new interface driver ath9k_htc [ 13.677661] usbcore: registered new interface driver cdc_acm [ 13.683360] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 13.753612] usbcore: registered new interface driver usbserial [ 13.759528] usbcore: registered new interface driver usbserial_generic [ 13.766157] usbserial: USB Serial support registered for generic [ 13.783160] Initializing USB Mass Storage driver... [ 13.788171] usbcore: registered new interface driver usb-storage [ 13.794211] USB Mass Storage support registered. [ 13.856516] usbcore: registered new interface driver ums-alauda [ 13.871246] usbcore: registered new interface driver ums-cypress [ 13.885809] usbcore: registered new interface driver ums-datafab [ 13.900071] usbcore: registered new interface driver ums-freecom [ 13.914553] usbcore: registered new interface driver ums-isd200 [ 13.928888] usbcore: registered new interface driver ums-jumpshot [ 13.943433] usbcore: registered new interface driver ums-karma [ 13.957768] usbcore: registered new interface driver ums-sddr09 [ 13.972145] usbcore: registered new interface driver ums-sddr55 [ 13.986734] usbcore: registered new interface driver ums-usbat [ 14.030549] usbcore: registered new interface driver asix [ 14.090829] usbcore: registered new interface driver cdc_ether [ 14.145884] usbcore: registered new interface driver sierra_net [ 14.199343] usbcore: registered new interface driver ftdi_sio [ 14.205205] usbserial: USB Serial support registered for FTDI USB Serial Device [ 14.265067] usbcore: registered new interface driver pl2303 [ 14.270727] usbserial: USB Serial support registered for pl2303 [ 14.285826] usbcore: registered new interface driver sierra [ 14.291472] usbserial: USB Serial support registered for Sierra USB modem [ 14.431176] u32 classifier [ 14.433921] Performance counters on [ 14.437762] input device check on [ 14.441427] Actions configured [ 14.482749] Mirror/redirect action on [ 14.553308] usbip_core: module is from the staging directory, the quality is unknown, you have been warned. [ 14.564541] usbip_core: USB/IP Core v1.0.0 [ 14.577012] vhci_hcd: module is from the staging directory, the quality is unknown, you have been warned. [ 14.587608] vhci_hcd vhci_hcd: USB/IP Virtual Host Controller [ 14.593407] vhci_hcd vhci_hcd: new USB bus registered, assigned bus number 2 [ 14.601584] hub 2-0:1.0: USB hub found [ 14.605434] hub 2-0:1.0: 8 ports detected [ 14.609725] vhci_hcd: USB/IP 'Virtual' Host Controller (VHCI) Driver v1.0.0 [ 14.625007] usbip_host: module is from the staging directory, the quality is unknown, you have been warned. [ 14.852596] usbcore: registered new interface driver usbip-host [ 14.858530] usbip_host: USB/IP Host Driver v1.0.0 [ 17.580699] eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1) [ 17.590464] device eth0 entered promiscuous mode [ 19.572619] libphy: 2188000.ethernet:00 - Link is Up - 100/Full [ 19.578582] br-lan: port 1(eth0) entered forwarding state [ 19.584053] br-lan: port 1(eth0) entered forwarding state [ 21.582278] br-lan: port 1(eth0) entered forwarding state BusyBox v1.19.4 (2013-04-08 22:22:48 PDT) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (Bleeding Edge, r35953) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/# }}}