= Software Defined Radios - What are they? A software defined radio (SDR) is a radio which can modulate and demodulate radio signals through software commands provided by a computer. They typically use a dedicated FPGA to process the radio signals in the digital domain. Many support wide frequency bandwidths allowing them to monitor a wide range of radio transmissions. == When should I use one? Software defined radios can be used in any radio application. The Epiq Sidekiq Z2 used in this testing can tune to any frequency between 40Mhz and 6Ghz. That covers from FM radio to 5G cellular. Any radio transmission in this frequency can be monitored with this board. Here is a chart showing some of the common radio protocols in that spectrum. ||= Band =||= Frequency =||= Common Use =|| || Very Low Frequency (VLF) || 3kHz to 30kHz || Maritime radio, navigation || || Low Frequency (LF) || 30kHz to 300kHz || Maritime radio, navigation || || Medium Frequency (MF) || 300kHz to 3MHz || AM radio, Aviation radio, navigation || || High Frequency (HF) || 3MHz to 30Mhz || Amateur radio, NFC, aviation, weather || || Very High Frequency (VHF) || 30MHz to 300MHz || FM radio, VHF television || || Ultra High Frequency (UHF) || 300MHz to 3GHz || Mobile radio, Wifi, GPS, 4G, UHF television || || Super High Frequency (SHF) || 3GHz to 30GHz || Satellite, 5G, Wifi, || == Who is Epiq? From their website, "Epiq Solutions develops cutting edge tools for engineering teams and government-focused organizations requiring situational awareness and detailed insight into their RF environments in order to identify and act against wireless threats". Not only that they're nice guys, we know because we have worked with them for a long time. Check out their web page - [https://epiqsolutions.com/] = Configuring the Epiq Sidekiq Z2 to work with Gateworks Materials required: * Gateworks SBC with latest Gateworks-Ubuntu image installed (In this testing GW6300 was used) * Epiq Z2 * Two antennas * Serial Console and network connections to the Gateworks SBC The Z2 can be used independently of Gateworks products with its (included) USB adapter. Before connecting your Z2 to a Gateworks board it's best to verify it's functionality and check that your antenna connections are being made correctly. If you will be using [wiki:/SDR#ERA ERA] now is a good time to install it. == Hardware configuration Attach the Z2 to the Gateworks SBC in any slot where USB signaling is provided. Verify antennas are attached to RX and TX U.FL connectors on the Z2. == Software configuration Follow the instructions [wiki:/ubuntu#SSHServer here] to enable "root" access via SSH. This requires using the serial console. With that done log into the Gateworks via SSH as root. Now access the Z2 via serial console from the Gateworks SBC {{{#!bash screen /dev/ttyACM0 }}} Username "root" Password "epiq" Execute the following commands to switch the SDR into USB-CDC mode for Linux {{{#!bash fw_setenv udc_config_mode 1 reboot }}} After the SDR had completed its power cycle log back in and verify the changes have been made: {{{ fw_print_env udc_config_mode #udc_config_mode=1 will be displayed }}} Exit screen "ctrl + a", ":", "quit" Verify a network interface has been created, for this testing it is named eth2 {{{ root@focal-newport:~# dmesg |grep cdc_ether [ 12.619443] cdc_ether 3-1:1.0 eth2: register 'cdc_ether' at usb-0000:00:11.0-1, CDC Ethernet Device, 00:e0:22:01:7d:15 [ 12.619589] usbcore: registered new interface driver cdc_ether }}} {{{ root@focal-newport:~# ls /sys/class/net/ can0 eth0 eth1 eth2 lo }}} Assign the interface a DHCP address: {{{ dhclient eth2 }}} If config will show eth2 with the address 192.168.3.9, counterintuitively SSH connections can be made to the Z2 at the 192.168.3.1 address "ssh root@192.168.3.1" == ERA ERA is Epiq's proprietary RF analyzer software. Check it out [https://epiqsolutions.com/rf-sensing/era/ here] Install Epiq ERA software on the Z2, instructions and files provided by Epiq. Launch ERA and allow the shell to run == Port forwarding using nftables to access ERA from your workstation Nftables allows packets to be forwarded from the Gateworks network interface to the Z2 interface and back out to an external network. This will allow access to the ERA web interface from a desktop workstation browser Install nftables and start the service {{{#!bash apt install nftables -y systemctl enable nftables.service systemctl start nftables.service }}} Check if ip forwarding is enabled, by default it is not. {{{#!bash root@focal-newport:~# sysctl net.ipv4.ip_forward net.ipv4.ip_forward = 1 #0 is disabled }}} To enable ip forwarding {{{#!bash sudo sed -i 's/#net.ipv4.ip_forward=1/net.ipv4.ip_forward=1/g' /etc/sysctl.conf sudo sysctl -p }}} Configure nftables by copying these commands individually, replace 192.168.0.1 with the IP address of the interface on the Gateworks which is connected to your network (the same used for connecting with SSH) {{{#!bash nft flush ruleset # clear existing rule set nft add table nat nft 'add chain nat postrouting { type nat hook postrouting priority 100 ; }' nft 'add chain nat prerouting { type nat hook prerouting priority -100; }' nft 'add rule nat prerouting ip daddr 192.168.0.1 tcp dport { 3000 } dnat 192.168.3.1:3000' nft add rule nat postrouting masquerade }}} Verify your changes {{{#!bash nft list ruleset }}} Make the ruleset persistant {{{#!bash nft list ruleset | tee /etc/nftables.conf }}} Open a web browser on your workstation, connect to the running ERA server by typing 192.168.0.1:3000, really :3000 Enjoy ERA from your workstation.