[[PageOutline]]

= Enclosures =
Gateworks sells a variety of enclosures on their online shop seen here: [http://shop.gateworks.com/index.php?route=product/category&path=76 Gateworks Online Shop - Enclosures]

== Newport Indoor Enclosures
 * The Newport Indoor Enclosures are built slightly taller to accomodate the fansink that is on the Newport SBCs. Additionally the side plates have holes for venting / cooling.

All Newport enclosures can be seen: [https://shop.gateworks.com/index.php?route=product/category&path=76_77_93 Gateworks Newport Enclosures]


== Indoor Ventana Enclosures ==

=== Installation Instructions ===
 * Heatsink
  * The enclosures are designed to heatsink the processor on the SBC to the metal enclosure for better heat dissipation. This is optional and a choice of the customer. The enclosure is supplied with a solid aluminum block. To use this, remove any heatsink currently on the processor and replace with the aluminum block heatsink as shown in the picture below:
  * [[Image(enclosureheatsink.jpg,400px)]]
 * Mounting SBC
  * Remove front plate of enclosure and pull out bottom plate that has standoffs on it.
  * Place the board 'upside down' on the standoffs and screw in 4 screws as shown below
  * [[Image(enclosurestandoffs.jpg,400px)]]
  * Remove front plate of enclosure  and slide in bottom plate and board as shown below:
   * [[Image(enclosurefront.jpg,400px)]]
  * Re-attach front plate and see the final product:
   * [[Image(enclosure.jpg,400px)]]

=== Din Rail Clip ===
The Ventana, Newport, and Venice Indoor enclosures can be fitted with a DIN Rail clip.

Two holes have been slightly punched to allow for customer drilling.

Din Rail Clip: [http://shop.gateworks.com/index.php?route=product/product&product_id=162 GW10092]

Screws to mount to enclosure are DIN74-Am4 which means a 90Deg countersink, with 4mm Metric screw. These can be seen here: [http://www.mcmaster.com/#92010a216/=x61x47 Example Screw]

Drill bit size: 11/64th or !#18 drill bit

[[Image(enclosuredinholes.jpg)]]

== Waterproof (IP6x) & Hazardous Enclosures / Third Party Enclosures

Abtech manufactures off the shelf enclosures that can be used in outdoor and hazardous locations. 
 * [https://www.abtech-inc.com]
 * The Zag models are popular and can be customized with cutouts for SMA, Ethernet and other connectors.  
  * [https://www.abtech-inc.com/products/enclosures/industrial-enclosures/marine-grade-aluminium-enclosure-zag.html]

Amphenol LTW is a good source for IP rated outdoor connectors. See link here:
* [https://www.amphenolltw.com/]

== Labels & Customizing

Gateworks understands there are times when a custom labeled enclosure is needed. 

The following options exist:
 * Remove the top plate that shows the Gateworks logo and flip it around so the back side shows and the Gateworks logo can't be seen
 * Have a custom made label with adhesive backing custom made and place on top of the Gateworks logo (read more below)
 * Contact Gateworks Sales Team directly to have a custom enclosure made with your company logo. This usually requires a minimum of at least 100 pieces and will require a setup fee, typically starting around $450 but could vary. 

==== Custom Adhesive Label
There are scenarios where a label / sticker can be applied to the standard Gateworks indoor enclosures for company branding. 

In the past, Gateworks customers have used labels with the following properties:
 * Label Material: Textured Polycarbonate Laminate - scratch resistant, scuff resistance and UV resistance.
 * Adhesive: Permanent Adhesive
 * Thickness: 6mil (.006 inch) total 
 * Corners: Square, NON-Rounded
 * Size: Measured to fit on top panel of enclosures. Size will vary depending on enclosure size, taken into account the corner pieces.
 * Vendor: [https://www.lolareddesign.com/]