[[Image(3ggraphic.png)]] ----- = Cellular Modems (GSM/GPRS/EDGE/UMTS/HSPA/LTE) = [[PageOutline]] M2M Cellular modems allow embedded systems to communicate and connect to the network in places that may not have other standard connections such as !WiFi or Ethernet. Embedded systems are being deployed in more remote locations that still require and mandate an internet connection. Gateworks boards have Mini-PCI-Express slots that allow for a wide range of cellular modems to be connected. You will find below examples and setup instructions for many devices Gateworks has qualified. Please check with Sierra Wireless for availability and EOL status. M2M cellular modems operate as a point-to-point serial device. Typically they are used as IP network interfaces by initiating a connection to a cellular carrier using standard AT modem commands then running {{{pppd}}} which performs CHAP authentication and implements the PPP protocol. The {{{pppd}}} daemon uses the {{{chat}}} application for AT command scripts and creates a network interface once authentication succeeds. Some devices expose more than one serial interface for things like AT commands, proprietary API's, NMEA data from optional GPS etc can be used while the network is connected. As a general rule, you need to have obtained the following from your Service Provider to use M2M devices in linux: * (4G) LTE and (3G) GSM modems: * A SIM card and the following details: * APN - Access Point Name * unlocked - or you need the PIN to unlock it (the SIM must not be locked to another device) * username - often optional but may be required by your provider * password - often optional but may be required by your provider * (3G) UMTS modems: * A modem that has been previously 'activated' by your provider. This involves providing the provider with the IMEI (unique identifier on the modem/module), the provider adding it to their system, and you 'activating' the module (which usually requires a Windows PC and application if not already done by the provider of the module) This information has been tested and created for use on the Gateworks Single Board Computers (SBCs)''', specifically the Ventana family that utilizes the Freescale i.MX6 processors. Gateworks SBCs can be viewed at the following link: [http://www.gateworks.com] [[Image(http://trac.gateworks.com/raw-attachment/wiki/OpenWrt/wireless/relayd/gw5100realsmall.png,200px)]] [=#carrier-certification] == Carrier Approval / Certification == Production hardware needs to be '''Carrier Approved''' - a process that the end-customer needs to work through with the M2M Carrier (Cellular provider) on the finished device. FCC Certification should be considered as well. The Cellular Carrier dictates if your plan provides 'mobile termination' (the ability to accept connections from the Internet) and the IP address provisioning (IP class, static vs dynamic, IP range). For GSM Carriers this is based on the APN. Products that use USA cellular networks typically need to be certified with the network. Some Mini-PCIe modems are pre-certified, however the product as a whole (enclosure, SBC, antenna) may still need to be certified. Gateworks recommends contacting the network provider of choice for more information. Additional links: * Connected IO modem Gateworks has used and is a supplier for which is pre-certified for Verizon: https://www.connectedio.com/products/details/17-lt1002-4g-lte-m2m-modem * Another certified modem that Gateworks has seen available on the Aeris network that is end-certified: http://www.multitech.com/datasheets/86002165.pdf * [http://ei.att.com/media/att/2013/emerging_devices/chooseATT/pdf/hardware-development-best-practices-2013.pdf AT&T Certification White Paper] - A very informative read for AT&T Network [=#recommended] == Recommended Modems == It is difficult to suggest modems because of pin signal and voltage conflicts listed [#conflicts here] However, the following modems can be recommended: * [#ublox U-Blox Toby L2] [=#conflicts] == Pin Signal and Voltage Conflicts == Many modems do not follow the Mini-PCIe pin specification. Gateworks designs the Mini-PCIe slots to strictly adhere to the formal specification by PCI SIG. Thus Gateworks typically find pin conflicts (signal mismatch or voltage differences) on the following pins: * Pin 11 (REFCLK-) * Pin 13 (REFCLK+) * Pin 20 (WDIS#) * Pin 22 (PERST#) * Pin 31 (PETN0) * Pin 33 (PETP0) Mini-PCIe pinout can be found in the [http://www.gateworks.com/usermanuals user manual] Please compare the modem pinout to the Gateworks pinout to ensure compatibility. Some Gateworks SBCs have special resistor loading to eliminate some of these conflicts. Please contact Gateworks support (support at gateworks.com) to learn more. === Specific Modems With Known Conflicts * Huawei MU609 * Sierra Wireless MC7455 * Sierra Wireless HL7588 * Sierra Wireless MC7354 * Quectel EC25-A * Telit LM940 If one of these modems must be used, email Gateworks support (support at gateworks.com) to learn more about resistor loading that may eliminate these conflicts. [=#usb3] == USB 3.0 Support == Some modems now support USB 3.0 for faster speeds required for Cat6. Gateworks routes USB 3.0 to select Mini-PCIe slots on the Newport GW62xx, GW63xx and GW64xx (the GW61xx only has USB 2.0). The Laguna and Ventana families do not support USB 3.0. USB 3.0 is typically routed through a Multiplexer shared with PCIe so proper configuration must happen at the bootloader layer described [wiki:newport/bootloader#hwconfig:miniPCIeSocketConfigurationhere] USB 3.0 pins on the miniPCIe connector are: * 23 - USB3.0_TX- * 25 - USB3.0_TX+ * 31 - USB3.0_RX- * 33 - USB3.0_RX+ Many of these devices support USB 2.0 as a fallback. To verify proper USB 3.0 link for a device look for that particular device with a 5000mbps speed as opposed to a 480mbps speed. For example: {{{#!bash root@xenial-newport:~# lsusb -t /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/1p, 5000M |__ Port 1: Dev 2, If 0, Class=Vendor Specific Class, Driver=option, 5000M |__ Port 1: Dev 2, If 1, Class=Vendor Specific Class, Driver=, 5000M |__ Port 1: Dev 2, If 2, Class=Vendor Specific Class, Driver=qmi_wwan, 5000M |__ Port 1: Dev 2, If 3, Class=Vendor Specific Class, Driver=option, 5000M |__ Port 1: Dev 2, If 4, Class=Vendor Specific Class, Driver=option, 5000M |__ Port 1: Dev 2, If 5, Class=Vendor Specific Class, Driver=option, 5000M |__ Port 1: Dev 2, If 6, Class=Vendor Specific Class, Driver=option, 5000M /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/1p, 480M /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/1p, 5000M |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 5000M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/1p, 480M |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/5p, 480M |__ Port 5: Dev 3, If 0, Class=Vendor Specific Class, Driver=, 480M }}} * Note above the 'qmi_wwan' device shows a 5000mbps link [=#firmware] == Modem Firmware == Modems typically require non-volatile firmware that gets flashed onto the device. This firmware is available from the modem manufacturer and/or carrier. Often you will need a different firmware version for different carriers and the firmware can also drastically change the behavior and control protocol the modem uses. Often vendor/carriers support only a Windows utility to update the firmware in which case you will need a miniPcie-to-USB adapter to put the modem on a PC. Qualcomm's QMI based modems can update their firmware using [#libqmi-firmware libqmi-firmware] [=#terminology] == Modem Terminology == * 3G : 3G has an average speed of around 1Mb/s * 4G : 4th Generation of mobile communications technology meeting requirements defined by ITU (International Telecommunications Union) in IMT Advanced. LTE or !WiMax. * LTE : (Long Term Evolution) - Considered 4G. * HSPA+ :High Speed Packet Access Plus - Considered 3G. theoretical top speed of 21Mb/s. Average is around 4Mb/s. * Frequency Bands - Many carriers and technologies utilize different radio frequencies. Confirming the cellular radio operates on the same frequencies as the targeted provider is required for proper operation. * Reference Links * http://www.androidauthority.com/4g-vs-lte-274882/ [=#control] == Modem Control == Unlike typical ethernet network interfaces, modem's require additional configuration and control to perform the following types of details before moving on to configuring a network interface: * Dialing - in the old days for dial-up modems * SIM pin control and unlocking (security) * Network provider registration * Data Protocol selection Once all of the above is complete a modem driver will provide a network interface to the Linux OS: * IP over ethernet * raw IP * IP over serial (sometimes via PPP daemon) And once you finally have an IP networking interface up and running from the modem, you can use the standard IP configuration tools within Linux (like !NetworkManager or the lower-level tools such as ip, route, ifconfig, etc) Over the years various different modem control protocols have been developed: * AT commands (text commands and responses typically preceded by 'AT' and terminated with a CR (carriage return or 0x0d) * QMI - Qualcomm Modem Interface (A binary protocol used for modern Qualcomm based modems) * MBIM - Mobile Interface Broadband Model (A new standard by the USB Implementers Forum specifying a new MBIM USB device model with multiple IP connections over a single USB interface without the need of 802.3 frames and a new MBIM control protocol [=#at] === AT commands === If your modem/firmware/driver provides an AT command control interface you will have a serial device which you send AT commands and receive responses. While many modems share common AT commands, each modem/manufacturer typically has their own set of extensions. You can use any typical terminal program such as 'screen', 'minicom', 'picocom' or even simply stty/echo/cat to communicate. Be aware of translations that may occur based on your terminal and/or configuration of these terminal programs. For example, modem AT interpreters expect to receive commands terminated by a CR (carriage return, hex 0x0d code) and will not respond if your terminal program is translating CR's to LF's (beware of using screen within a screen session for example, which will do this). Modems should auto-baud meaning they should support a variety of baudrates. Typical settings would be 57600baud, 8 data bits, 1 stop bit, no parity (8N1). Some examples (assuming /dev/ttyUSB0 is your modem's control interface) * picocom (recommended) {{{#!bash picocom /dev/ttyUSB -b 9600 --omap lfcr }}} * minicom {{{#!bash minicom --device /dev/ttyUSB0 --baudrate 57600 }}} * screen * NOTE: a screen session for AT commands within another screen session may {{{#!bash screen /dev/ttyUSB0 57600 }}} * stty/cat/echo: {{{#!bash stty -F /dev/ttyUSB0 ignbrk -brkint -icrnl -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke cat /dev/ttyUSB0 & echo -e "ATI\n" > /dev/ttyUSB0 }}} [=#mbim] === Mobile Interface Broadband Model (MBIM) === Mobile Interface Broadband Model (MBIM) is a new standard by the USB Implemented Forum. It specifies a new MBIM USB device model providing multiple IP connections over a single USB interface without the need of 802.3 frames (which was the case for ECM and NCM) and a new MBIM control protocol to talk to modem devices. See also: * [wiki:wireless/modem#libmbim libmbim] [=#qmi] === Qualcomm MSM Interface (QMI) === The Qualcomm MSM Interface (QMI) is a modem control protocol that appears in many modern Qualcomm based modems. QMI defines different services: - DMS: Device Management - load device info - NAS: Network Access - register in the network - WDS: - request data connections - PDS: - setup GPS location reporting - UIM: - manage internals of the user identity module See also: * [wiki:wireless/modem#libqmi libqmi] * [wiki:wireless/modem#uqmi uqmi] [=#link-protocol] ==== Link Protocols ==== QMI modems support multiple link protocols: - 802-3: wraps IP packets within Ethernet frames (similar to an Ethernet device) like traditional modems - raw-ip: does away with the Ethernet layer and provides raw IP frames which is more efficient and allows higher throughput, but disallows things that rely on 802-3 such as DHCP Some QMI modem/firmware/SIM combinations support 802-3 only, others support raw-ip only, and some support both. It is important to make sure the driver and the network device are configured to use the same link protocol. [=#ip-family] ==== IP Family ==== QMI modem/firmware/SIM combinations can support IPv4, IPv6, or both IP families. If you are trying to connect and receive an error related to IP family check that your asking for something supported. [=#client-cid] ==== Client ID ==== To use QMI services you need a 'Client ID' or CID. The CID's can be created then released when they are no longer needed. When working with sessions the CID is what allows QMI services to be operated on the right session. Both libqmi and uqmi userspace applications allow you to issue QMI commands by using an existing specified CID and to not release CID upon completion. It is important to use this when configuring and starting connections. For example, you can have an ipv4 session concurrent with an ipv6 session, each must have their own CID that is not released (until the connection is closed) and must be used when referring to those sessions. When using {{{qmicli}}} you do this with the {{{--client-cid=}}} and the {{{--client-no-release-cid}}} options. When using {{{uqmi}}} you obtain a client-id with the {{{--get-client-id}}} option and use an existing one with the {{{--get-client-id}}} option and release a CID with the {{{--release-client-id}}} option. [=#bsp] === Gateworks BSP Support === Gateworks supports multiple Board Support Packages. The following table shows details on modem support for each: ||= BSP =||= Product Families =||= AT =||= QMI =||= MBIM =||= Drivers =||= Notes =|| || [wiki:Android] || Ventana || No || No || No || None || [http://trac.gateworks.com/wiki/Android#CellularModemNetworking See Freescale information] || || [wiki:Yocto Yocto] || Ventana || manual || No || No || Minimal || || || OpenWrt || All || comgt || uqmi || umbim || Many || || || [wiki:ventana/ubuntu Ubuntu] || Ventana || !ModemManager || libqmi || libmbim || Many || [https://wiki.ubuntu.com/ConnMan/Hardware/3G] || || [wiki:ventana/debian Debian ] || Ventana || !ModemManager || libqmi || libmbim || Many || [https://wiki.debian.org/Modem/3G] || If you are looking for additional support please contact support@gateworks.com [=#linux] == Linux Drivers == There are several Linux kernel drivers used for modem technology. You should enable all of these depending on your device needs: * qcserial / USB_SIERIAL_QUALCOMM - Provides serial tty devices for Qualcomm modems * sierra / USB_SERIAL_SIERRAWIRELESS - Provides serial tty devices for Sierra Wireless modems * option / USB_SERIAL_OPTION - USB driver for GSM and CDMA modems with built-in OHCI-USB adapter (Option, Huawei, Audiovox, Novatel, Anydata) * sierra_net / USB_SIERRA_NET - USB-to-WWAN driver for Sierra Wireless modems * cdc-acm / USB_ACM - USB Modem (CDC ACM) support * qmi_wwan / USB_NET_QMI_WWAN - QMI WWAN driver for Qualcomm modems based on QMI (Qualcomm Messaging Interface) * cdc_mbim / USB_NET_CDC_MBIM - CDC MBIM support: Provides support for CDC MBIM (Mobile Broadband Interface modem) devices. These all depend on the following Kernel features: * NETDEVICES=y * USB_NET_DRIVERS=y * USB_USBNET=y * USB_SERIAL [=#ubuntu] == Ubuntu Cellular Modem Support (libqmi/libmbim/modemmanager) == Ubuntu Linux systems utilize the following opensource projects for modem control and management: * libmbim * libqmi * modemmanager * networkmanager [=#modemmanager-ppa] === Installing pre-built latest stable libqmi/libmbim/modemmanager via PPA Aleksander Morgado (​https://aleksander.es), a key developer behind the !ModemManager, libqmi, and libmbim projects that provide modem support on Ubuntu provides up-to-date Ubuntu PPA's for Ubuntu. Instructions on how to add the PPA feeds and update the packages exist there: - [https://launchpad.net/~aleksander-m/+archive/ubuntu/modemmanager-bionic modemmanager/libqmi/libmbim PPA bionic] - [https://launchpad.net/~aleksander-m/+archive/ubuntu/modemmanager-xenial modemmanager/libqmi/libmbim PPA xenial] - [https://launchpad.net/~aleksander-m/+archive/ubuntu/modemmanager-trusty modemmanager/libqmi/libmbim PPA trusty] Bionic: {{{#!bash apt-get install software-properties-common # contains add-apt-repository add-apt-repository ppa:aleksander-m/modemmanager-bionic apt-get update apt-get install modemmanager libqmi-utils libmbim-utils policykit-1 }}} Xenial: {{{#!bash apt-get install software-properties-common # contains add-apt-repository add-apt-repository ppa:aleksander-m/modemmanager-xenial apt-get update apt-get install modemmanager libqmi-utils libmbim-utils policykit-1 }}} Trusty: {{{#!bash add-apt-repository ppa:aleksander-m/modemmanager-trusty apt-get update apt-get install modemmanager libqmi-utils libmbim-utils policykit-1 }}} see [#building-from-source below] for details on how to build even more up to date versions from source if needed. [=#libmbim] === libmbim === The libmbim library is a protocol support library much like libqmi is for QMI and has a {{{mbimcli}}} and {{{mbim-network}}} as well. Since libqmi-1.16.0 and libmbim-1.14.0 there is support for QMI-over-MBIM as well but not clear what is using this. !ModemManager is using libmbim directly as that is what vendors expect/test Useful Examples: * show status (useful for verifying SIM): {{{#!bash mbimcli --device /dev/cdc-wdm0 --query-subscriber-ready-status # should show "Ready state: 'initialized'" }}} * radio state (should show 'on') {{{#!bash mbimcli --device /dev/cdc-wdm0 --query-radio-state # should show on }}} - if not use '--set-radio-state=on' * enable FCCAuth (required on many Sierra Wireless devices) {{{#!bash qmicli --device /dev/cdc-wdm0 --device-open-proxy --device-open-mbim --dms-set-fcc-authentication }}} * verify signal state: {{{#!bash mbimcli --device /dev/cdc-wdm0 --device-open-proxy --query-signal-state # RSSI=99 is no signal }}} - Network {{{#!bash mbimcli --device /dev/cdc-wdm0 --device-open-proxy --query-preferred-providers mbimcli --device /dev/cdc-wdm0 --device-open-proxy --query-home-provider mbimcli --device /dev/cdc-wdm0 --device-open-proxy --query-visible-providers mbimcli --device /dev/cdc-wdm0 --device-open-proxy --query-registration-state [/dev/cdc-wdm0] Registration status: Network error: 'unknown' Register state: 'home' Register mode: 'automatic' Available data classes: 'lte' Current cellular class: 'gsm' Provider ID: '310260' Provider name: 'Project Fi' Roaming text: 'unknown' Registration flags: 'packet-service-automatic-attach' }}} - connect: * using mbim-network {{{#!bash root@ventana:~# echo "APN=h2g2" > /etc/mbim-network.conf # specify APN root@ventana:~# echo "PROXY=yes" >> /etc/mbim-network.conf # allow ports to be shared by multiple libmbim apps root@ventana:~# mbim-network /dev/cdc-wdm0 start Loading profile at /etc/mbim-network.conf... APN: h2g2 APN auth protocol: unset APN user: unset APN password: unset mbim-proxy: no Querying subscriber ready status 'mbimcli -d /dev/cdc-wdm0 --query-subscriber-ready-status --no-close '... [/dev/cdc-wdm0] Subscriber ready status retrieved: Ready state: 'initialized' Subscriber ID: '310260970524563' SIM ICCID: '8901260971105245631' Ready info: 'unknown' Telephone numbers: (1) '15309030245' [/dev/cdc-wdm0] Session not closed: TRID: '3' Saving state at /tmp/mbim-network-state-cdc-wdm0... (TRID: 3) Querying registration state 'mbimcli -d /dev/cdc-wdm0 --query-registration-state --no-open=3 --no-close '... [/dev/cdc-wdm0] Registration status: Network error: 'unknown' Register state: 'home' Register mode: 'automatic' Available data classes: 'lte' Current cellular class: 'gsm' Provider ID: '310260' Provider name: 'Project Fi' Roaming text: 'unknown' Registration flags: 'packet-service-automatic-attach' [/dev/cdc-wdm0] Session not closed: TRID: '4' Saving state at /tmp/mbim-network-state-cdc-wdm0... (TRID: 4) Attaching to packet service with 'mbimcli -d /dev/cdc-wdm0 --attach-packet-service --no-open=4 --no-close '... Saving state at /tmp/mbim-network-state-cdc-wdm0... (TRID: 5) Starting network with 'mbimcli -d /dev/cdc-wdm0 --connect=apn='h2g2' --no-open=5 --no-close '... Network started successfully Saving state at /tmp/mbim-network-state-cdc-wdm0... (TRID: 7) }}} * or manually {{{#!bash mbimcli --device /dev/cdc-wdm0 --device-open-proxy --connect=apn='h2g2' --no-open=5 --no-close }}} Notes: - MBIM modems do not implement DHCP shim functionality. You need to get the IP details for the interface with 'mbimcli --query-ip-configuration=' and apply those to the interface and update routing manually References: - https://sigquit.wordpress.com/2013/02/06/an-introduction-to-libmbim/ [=#libqmi] === libqmi === The libqmi library is a protocol support library much like libmbim is for MBIM and has a {{{qmicli}}} and {{{qmi-network}}} command-line tool as well. Since libqmi-1.16.0 and libmbim-1.14.0 there is support for QMI-over-MBIM as well but not clear what is using this. !ModemManager is using libqmi to control QMI based modems. ==== Command Line Examples ==== If not using a higher level manager which utilizes libqmi such as !ModemManager, you can use libqmi directly with the aforementioned tools '''(make sure !ModemManager is not installed or running if using libqmi directly!)''': * SIM details (UIM service): {{{#!bash root@ventana:~# qmicli -d /dev/cdc-wdm0 --uim-get-card-status [/dev/cdc-wdm0] Successfully got card status Provisioning applications: Primary GW: slot '0', application '0' Primary 1X: session doesn't exist Secondary GW: session doesn't exist Secondary 1X: session doesn't exist Card [0]: Card state: 'present' UPIN state: 'not-initialized' UPIN retries: '0' UPUK retries: '0' Application [0]: Application type: 'usim (2)' Application state: 'ready' Application ID: A0:00:00:00:87:10:02:FF:FF:FF:FF:89:06:19:00:00 Personalization state: 'ready' UPIN replaces PIN1: 'no' PIN1 state: 'disabled' PIN1 retries: '3' PUK1 retries: '10' PIN2 state: 'enabled-not-verified' PIN2 retries: '10' PUK2 retries: '10' Application [1]: Application type: 'isim (5)' Application state: 'detected' Application ID: A0:00:00:00:87:10:04:FF:FF:FF:FF:89:07:03:00:00 Personalization state: 'unknown' UPIN replaces PIN1: 'no' PIN1 state: 'disabled' PIN1 retries: '3' PUK1 retries: '10' PIN2 state: 'not-initialized' PIN2 retries: '0' PUK2 retries: '0' }}} * Signal strength: {{{#!bash root@ventana:~# qmicli -d /dev/cdc-wdm0 --nas-get-signal-info [/dev/cdc-wdm0] Successfully got signal info WCDMA: RSSI: '-96 dBm' ECIO: '-12.0 dBm' root@ventana:~# qmicli -d /dev/cdc-wdm0 --nas-get-signal-strength [/dev/cdc-wdm0] Successfully got signal strength Current: Network 'umts': '-96 dBm' RSSI: Network 'umts': '-96 dBm' ECIO: Network 'umts': '-11.0 dBm' IO: '-106 dBm' SINR (8): '9.0 dB' }}} * Network details (NAS service): {{{#!bash root@ventana:~# qmicli -d /dev/cdc-wdm0 --nas-get-system-selection-preference [/dev/cdc-wdm0] Successfully got system selection preference Emergency mode: 'no' Mode preference: 'umts, lte' Band preference: 'wcdma-2100, wcdma-pcs-1900, wcdma-dcs-1800, wcdma-1700-us, wcdma-850-us, wcdma-900' LTE band preference: '1, 2, 3, 4, 5, 7, 8, 12, 13, 20, 25, 41' TD-SCDMA band preference: '(null)' Roaming preference: 'any' Network selection preference: 'automatic' Service domain preference: 'cs-ps' Service selection preference: 'automatic' root@ventana:~# qmicli -d /dev/cdc-wdm0 --nas-network-scan [/dev/cdc-wdm0] Successfully scanned networks Network [0]: MCC: '310' MNC: '260' Status: 'available, home, not-forbidden, preferred' Description: 'T-Mobile' Network [1]: MCC: '310' MNC: '260' Status: 'current-serving, home, not-forbidden, preferred' Description: 'Project F' Network [2]: MCC: '312' MNC: '770' Status: 'available, roaming, not-forbidden, not-preferred' Description: '312 770' Network [3]: MCC: '310' MNC: '410' Status: 'available, roaming, not-forbidden, not-preferred' Description: 'AT&T' Network [4]: MCC: '310' MNC: '410' Status: 'available, roaming, not-forbidden, not-preferred' Description: 'AT&T' Network [5]: MCC: '311' MNC: '480' Status: 'available, roaming, forbidden, not-preferred' Description: 'Verizon' Network [0]: MCC: '310' MNC: '260' RAT: 'lte' Network [1]: MCC: '310' MNC: '260' RAT: 'umts' Network [2]: MCC: '312' MNC: '770' RAT: 'lte' Network [3]: MCC: '310' MNC: '410' RAT: 'lte' Network [4]: MCC: '310' MNC: '410' RAT: 'umts' Network [5]: MCC: '311' MNC: '480' RAT: 'lte' Network [0]: MCC: '310' MNC: '260' MCC with PCS digit: 'yes' Network [1]: MCC: '310' MNC: '260' MCC with PCS digit: 'yes' Network [2]: MCC: '312' MNC: '770' MCC with PCS digit: 'yes' Network [3]: MCC: '310' MNC: '410' MCC with PCS digit: 'yes' Network [4]: MCC: '310' MNC: '410' MCC with PCS digit: 'yes' Network [5]: MCC: '311' MNC: '480' MCC with PCS digit: 'yes' root@ventana:~# qmicli -d /dev/cdc-wdm0 --nas-get-operator-name [/dev/cdc-wdm0] Successfully got operator name data PLMN List: MCC/MNC: '310-DDD' LAC Range: 0->65279 PNN Record: 1 MCC/MNC: '311-DDD' LAC Range: 0->65279 PNN Record: 1 MCC/MNC: '312-DDD' LAC Range: 0->65279 PNN Record: 1 MCC/MNC: '313-DDD' LAC Range: 0->65279 PNN Record: 1 MCC/MNC: '314-DDD' LAC Range: 0->65279 PNN Record: 1 MCC/MNC: '315-DDD' LAC Range: 0->65279 PNN Record: 1 MCC/MNC: '316-DDD' LAC Range: 0->65279 PNN Record: 1 PLMN Names: 0: 'Project Fi' ('Project Fi') Country: 'initials-do-not-add' root@ventana:~# qmicli -d /dev/cdc-wdm0 --nas-get-serving-system [/dev/cdc-wdm0] Successfully got serving system: Registration state: 'registered' CS: 'attached' PS: 'attached' Selected network: '3gpp' Radio interfaces: '1' [0]: 'umts' Roaming status: 'off' Data service capabilities: '3' [0]: 'hsdpa' [1]: 'hsupa' [2]: 'wcdma' Current PLMN: MCC: '310' MNC: '260' Description: 'Project Fi' Roaming indicators: '1' [0]: 'off' (umts) 3GPP location area code: '26289' 3GPP cell ID: '85367600' Detailed status: Status: 'available' Capability: 'cs-ps' HDR Status: 'none' HDR Hybrid: 'no' Forbidden: 'no' Call barring status: Circuit switched: 'all-calls' Packet switched: 'all-calls' UMTS primary scrambling code: '61' Full operator code info: MCC: '310' MNC: '260' MNC with PCS digit: 'yes' root@ventana:~# qmicli -d /dev/cdc-wdm0 --nas-get-home-network [/dev/cdc-wdm0] Successfully got home network: Home network: MCC: '310' MNC: '260' Description: 'Project F' root@ventana:~# qmicli -d /dev/cdc-wdm0 --nas-get-system-info [/dev/cdc-wdm0] Successfully got system info: WCDMA service: Status: 'available' True Status: 'available' Preferred data path: 'no' Domain: 'cs-ps' Service capability: 'cs-ps' Roaming status: 'off' Forbidden: 'no' Location Area Code: '26289' Cell ID: '85367600' MCC: '310' MNC: '260' HS call status: 'hsdpa-hsupa-unsupported' HS service: 'hsdpa-hsupa-supported' Primary scrambling code: '61' Cell broadcast support: 'off' Call barring status (CS): 'all-calls' Call barring status (PS): 'all-calls' Cipher Domain: 'none' LTE service: Status: 'none' True Status: 'none' Preferred data path: 'no' SIM reject info: 'available' }}} * Configure [wiki:wireless/modem#link-protocol Link Protocol]: {{{#!bash root@ventana:~# qmicli -p -d /dev/cdc-wdm0 --wda-set-data-format=802-3 # set data format (raw-ip/802-3) root@ventana:~# qmicli -p -d /dev/cdc-wdm0 --set-expected-data-format=802-3 # set expected format, should match above }}} - '''Make sure you choose a link protocol (802-3 or raw-ip) that is compatible with your modem/firmware/SIM''' * Connect to Google Fi network (WDS service): {{{#!bash root@ventana:~# echo "APN=h2g2" > /etc/qmi-network.conf # specify APN root@ventana:~# echo "PROXY=yes" >> /etc/qmi-network.conf # allow ports to be shared by multiple libqmi apps root@ventana:~# qmi-network /dev/cdc-wdm0 start Loading profile at /etc/qmi-network.conf... APN: h2g2 APN user: unset APN password: unset qmi-proxy: no Checking data format with 'qmicli -d /dev/cdc-wdm0 --wda-get-data-format --device-open-proxy'... Device link layer protocol retrieved: raw-ip Getting expected data format with 'qmicli -d /dev/cdc-wdm0 --get-expected-data-format'... Expected link layer protocol retrieved: 802-3 Updating kernel link layer protocol with 'qmicli -d /dev/cdc-wdm0 --set-expected-data-format=raw-ip'... Kernel link layer protocol updated Starting network with 'qmicli -d /dev/cdc-wdm0 --wds-start-network=apn='h2g2' --client-no-release-cid '... Saving state at /tmp/qmi-network-state-cdc-wdm0... (CID: 35) Saving state at /tmp/qmi-network-state-cdc-wdm0... (PDH: 62482624) Network started successfully }}} * Configuring IP: - If your modem/firmware/SIM combination supports {{{802-3}}} link protocol and is configured to do so, you can use DHCP: {{{#!bash root@ventana:~# dhclient wwan0 }}} - or, you can use {{{-wds-get-current-settings}}} to obtain the settings provided to the conneciton from the carrier and configure them manually. Take care to use the same {{{client-cid}}} that was returned from the {{{-wds-start-network}}} command and to not release the client-id: {{{#!bash root@ventana:~# qmicli --device /dev/cdc-wdm0 --client-no-release-cid --client-cid=35 --wds-get-current-settings [/dev/cdc-wdm0] Current settings retrieved: IP Family: IPv4 IPv4 address: 100.69.157.123 IPv4 subnet mask: 255.255.255.248 IPv4 gateway address: 100.69.157.124 IPv4 primary DNS: 10.177.0.34 IPv4 secondary DNS: 10.177.0.210 MTU: 1500 Domains: none [/dev/cdc-wdm0] Client ID not released: Service: 'wds' CID: '35' root@ventana:~# ifconfig wwan0 100.69.157.123 netmask 255.255.255.248 root@ventana:~# route add default gw 100.69.157.124 wwan0 root@ventana:~# echo "nameserver 10.177.0.34" > /etc/resolv.conf root@ventana:~# echo "nameserver 10.177.0.210" >> /etc/resolv.conf root@ventana:~# ping www.google.com }}} Troubleshooting QMI connection issues: - make sure you are using a [wiki:wireless/modem#link-protocol Link Protocol] compatible with your modem/firmware/SIM - make sure you are using an [wiki:wireless/modem#ip-family IP Family] compatible with your modem/firmware/SIM - don't use DHCP if its not supported by your carrier or if your not using the 802-3 link protocol - instead use 'wds-get-current-settings' and manually configure the interface - make sure you are not releasing the [wiki:wireless/modem#client-id Client ID] when connecting to the network [=#libqmi-firmware] Firmware related commands: * Show firmware versions {{{#!bash root@ventana:~# qmicli -d /dev/cdc-wdm0 --dms-get-firmware-preference firmware preference successfully retrieved: [image 0] Image type: 'modem' Unique ID: '005.010_001' Build ID: '05.05.16.02_ATT' [image 1] Image type: 'pri' Unique ID: '005.010_001' Build ID: '05.05.16.02_ATT' }}} * update firmware: {{{#!bash root@ventana:~/mc7354/firmware# qmi-firmware-update --update -d 1199:68c0 9999999_9902196_SWI9X15C_05.05.58.00_00_ATT_005.026_000-field.spk loading device information before the update... setting firmware preference: firmware version: '05.05.58.00' config version: '005.026_000' carrier: 'ATT' rebooting in download mode... download mode detected downloading cwe image: 9999999_9902196_SWI9X15C_05.05.58.00_00_ATT_005.026_000-field.spk (34.8 MB)... finalizing download... (may take more than one minute, be patient) successfully downloaded in 11.31s (3.1 MB/s) rebooting in normal mode... normal mode detected ------------------------------------------------------------------------ NOTE: in order to validate which is the firmware running in the module, the program will wait for a complete boot; this process may take some time and several retries. ------------------------------------------------------------------------ waiting some time for the device to boot... loading device information after the update (1/12)... waiting some time for the device to boot... loading device information after the update (2/12)... waiting some time for the device to boot... loading device information after the update (3/12)... ------------------------------------------------------------------------ original firmware revision was: SWI9X15C_05.05.16.02 r21040 carmd-fwbuild1 2014/03/17 23:49:48 original running firmware details: Model: MC7354 Boot version: SWI9X15C_05.05.16.02 r21040 carmd-fwbuild1 2014/03/17 23:49:48 AMSS version: SWI9X15C_05.05.16.02 r21040 carmd-fwbuild1 2014/03/17 23:49:48 SKU ID: 1102016 Package ID: 1102016_9903211_SWI9X15C_05.05.16.02_00_Generic_005.006_000 Carrier ID: 4 original firmware preference details: image 'modem': unique id '005.010_001', build id '05.05.16.02_ATT' image 'pri': unique id '005.010_001', build id '05.05.16.02_ATT' new firmware revision is: SWI9X15C_05.05.58.00 r27038 carmd-fwbuild1 2015/03/04 21:30:23 new running firmware details: Model: MC7354 Boot version: SWI9X15C_05.05.58.00 r27038 carmd-fwbuild1 2015/03/04 18:38:46 AMSS version: SWI9X15C_05.05.58.00 r27038 carmd-fwbuild1 2015/03/04 21:30:23 SKU ID: 1102016 Package ID: 1102016_9903211_SWI9X15C_05.05.16.02_00_Generic_005.006_000 Carrier ID: 4 new firmware preference details: image 'modem': unique id '005.026_000', build id '05.05.58.00_ATT' image 'pri': unique id '005.026_000', build id '05.05.58.00_ATT' NOTE: this device supports firmware preference management with qmicli operations: --dms-get-firmware-preference --dms-set-firmware-preference ------------------------------------------------------------------------ firmware update operation finished successfully }}} References: * libqmi - http://www.freedesktop.org/wiki/Software/libqmi/ * An introduction to libqmi - http://sigquit.wordpress.com/2012/08/20/an-introduction-to- * [=#modemmanager] === !ModemManager === !ModemManager is a package containing a background service/daemon and a command-line-interfalce (mmcli) that can be used to configure and connect modems. Note that after starting the service (if manually started) it does take 20 to 30 seconds to finish modem detection. Example usage: - List detected modems {{{#!bash root@ventana:~# mmcli --list-modems No modems were found root@ventana:~# mmcli --list-modems Found 1 modems: /org/freedesktop/ModemManager1/Modem/0 [Sierra Wireless, Incorporated] MC7455 }}} - Show details for the first modem: {{{#!bash root@ventana:~# mmcli --modem 0 /org/freedesktop/ModemManager1/Modem/0 (device id '86bde2905ff6f63bbefcfa457fe8f9221b76e968') ------------------------- Hardware | manufacturer: 'Sierra Wireless, Incorporated' | model: 'MC7455' | revision: 'SWI9X30C_02.08.02.00 r5428 CARMD-EV-FRMWR2 2016/01/06 20:38:53' | supported: 'gsm-umts | lte | gsm-umts, lte' | current: 'gsm-umts, lte' | equipment id: '359072060290422' ------------------------- System | device: '/sys/devices/soc0/soc/2100000.aips-bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.2' | drivers: 'qmi_wwan, qcserial' | plugin: 'Sierra' | primary port: 'cdc-wdm0' | ports: 'ttyUSB0 (qcdm), ttyUSB2 (at), cdc-wdm0 (qmi), wwan0 (net), wwan1 (net), cdc-wdm1 (qmi)' ------------------------- Numbers | own : '18057812000' ------------------------- Status | lock: 'sim-pin2' | unlock retries: 'sim-pin (3), sim-pin2 (10), sim-puk (10), sim-puk2 (10)' | state: 'disabled' | power state: 'on' | access tech: 'unknown' | signal quality: '0' (cached) ------------------------- Modes | supported: 'allowed: 2g, 3g, 4g; preferred: none' | current: 'allowed: 2g, 3g, 4g; preferred: none' ------------------------- Bands | supported: 'u2100, u1800, u1900, u17iv, u850, u900, eutran-i, eutran-ii, eutran-iii, eutran-iv, eutran-v, eutran-vii, eutran-viii, eutran-xii, eutran-xiii, eutran-xx, eutran-xxv, eutran-xli' | current: 'u2100, u1800, u1900, u17iv, u850, u900, eutran-i, eutran-ii, eutran-iii, eutran-iv, eutran-v, eutran-vii, eutran-viii, eutran-xii, eutran-xiii, eutran-xx, eutran-xxv, eutran-xli' ------------------------- IP | supported: 'ipv4, ipv6, ipv4v6' ------------------------- 3GPP | imei: '359072060290555' | enabled locks: 'none' | operator id: 'unknown' | operator name: 'unknown' | subscription: 'unknown' | registration: 'unknown' ------------------------- SIM | path: '/org/freedesktop/ModemManager1/SIM/0' ------------------------- Bearers | paths: 'none' }}} * Note the above shows a Sierra Wireless MC7455 modem supporting 'gsm-umts', 'lte' networks, using QMI control protocol (qmi_wwan driver) on /dev/cdc-wdm0, with a SIM that has been read however the radio is disabled - If the SIM has PIN locking enabled and its state is 'locked' under the Status section above you can enter the SIM pin with {{{mmcli --pin=}}} {{{#!bash root@ventana:~# mmcli --pin=1234 successfully sent PIN code to the SIM }}} * Some additional commands for handling SIM PINs are '--enable-pin', '--disable-pin', '--change-pin=', '--puk=' to enable PIN locking, disable PIN locking, changing the PIN, and unlocking a PUK-locked ([https://en.wikipedia.org/wiki/Personal_unblocking_code Personal unblocking code]) SIM. - Enable first modem: {{{#!bash root@ventana:~# mmcli --modem 0 --enable successfully enabled the modem }}} - if you get a failure here, make sure that the status shown by the {{{mmcli --modem 0}}} above does not show a failure. The modem can not be enabled if there is a failure * Now a status will show the following different info under status {{{#!bash ------------------------- Status | lock: 'sim-pin2' | unlock retries: 'sim-pin (3), sim-pin2 (10), sim-puk (10), sim-puk2 (10)' | state: 'registered' | power state: 'on' | access tech: 'umts' | signal quality: '26' (recent) }}} - Scan available networks: {{{#!bash root@ventana:~# mmcli --modem 0 --3gpp-scan --timeout=300 Found 5 networks: 310410 - AT&T (umts, available) 310410 - AT&T (lte, available) 310260 - T-Mobile (gsm, available) 310260 - Project Fi (umts, current) 310260 - T-Mobile (lte, available) }}} - Connect modem (example: Google Fi) {{{#!bash root@ventana:~# mmcli --modem 0 --simple-connect="apn=h2g2" successfully connected the modem }}} - Get IP Configuration: {{{ root@ventana:~# mmcli --modem 0 | grep Bearers Bearers | paths: '/org/freedesktop/ModemManager1/Bearer/0' root@ventana:~# mmcli --bearer 0 Bearer '/org/freedesktop/ModemManager1/Bearer/0' ------------------------- Status | connected: 'yes' | suspended: 'no' | interface: 'wwan0' | IP timeout: '20' ------------------------- Properties | apn: 'h2g2' | roaming: 'allowed' | IP type: 'none' | user: 'none' | password: 'none' | number: 'none' | Rm protocol: 'unknown' ------------------------- IPv4 configuration | method: 'static' | address: '30.58.51.96' | prefix: '30' | gateway: '30.58.51.97' | DNS: '10.177.0.34', '10.177.0.210' | MTU: '1430' ------------------------- IPv6 configuration | method: 'unknown' ------------------------- Stats | Duration: '30' | Bytes received: 'N/A' | Bytes transmitted: 'N/A' root@ventana:~# ifconfig wwan0 30.58.51.96/30 root@ventana:~# route add default gw 30.58.51.97 wwan0 root@ventana:~# echo "nameserver 10.177.0.34" > /etc/resolv.conf root@ventana:~# echo "nameserver 10.177.0.210" >> /etc/resolv.conf root@ventana:~# ping www.google.com }}} * Some modem drivers provide 'raw-ip' instead of 802.3 link layer which DHCP doesn't support requiring you to manually configure as above. If your modem provides an 802.3 channel you can run dhcp via 'dhclient wwan0' Some modems that support GNSS provide access to global positioning via !ModemManager. For example, the Huawei MU609: {{{#!bash # enable GPS based location with NMEA trace info root@ventana:~# mmcli --modem 0 --location-enable-gps-nmea successfully setup location gathering # get GPS NMEA location info root@ventana:~# mmcli --modem 0 --location-get-gps-nmea /org/freedesktop/ModemManager1/Modem/0 ------------------------- GPS NMEA traces | $GPGGA,153824.0,3515.484477,N,12040.136651,W,1,06,1.3,47.8,M,-31.0,M,,*58 | $GPGSA,A,3,05,07,08,09,28,30,,,,,,,2.7,1.3,2.4*39 | $GPVTG,,T,0.0,M,0.0,N,0.0,K,A*0D | $GPRMC,153824.0,A,3515.484477,N,12040.136651,W,0.0,,200617,,,A*56 | $GPGSV,2,1,07,05,17,289,36,07,60,040,40,08,35,064,32,09,47,154,35*78 | $GPGSV,2,2,07,28,54,239,38,30,54,319,39,23,15,146,*43 # enable GPS based location with raw trace info root@ventana:~# mmcli --modem 0 --location-enable-gps-raw successfully setup location gathering root@ventana:~# mmcli --modem 0 --location-get-gps-raw /org/freedesktop/ModemManager1/Modem/0 ------------------------- Raw GPS | UTC time: '153938.0' | Longitude: '-120.668886' | Latitude: '35.258143' | Altitude: '46.100000' root@ventana:~# mmcli --modem 0 --location-get /org/freedesktop/ModemManager1/Modem/0 ------------------------- 3GPP location | Mobile country code: '310' | Mobile network code: '410' | Location area code: '55562' | Cell ID: '53228154' ------------------------- GPS NMEA traces | $GPGGA,153938.0,3515.488596,N,12040.133136,W,1,06,1.3,46.1,M,-31.0,M,,*5D | $GPGSA,A,3,05,07,08,09,28,30,,,,,,,2.7,1.3,2.3*3E | $GPVTG,,T,0.0,M,0.0,N,0.0,K,A*0D | $GPRMC,153938.0,A,3515.488596,N,12040.133136,W,0.0,,200617,,,A*5B | $GPGSV,2,1,07,05,17,289,35,07,60,042,41,08,35,063,34,09,46,154,35*78 | $GPGSV,2,2,07,28,54,240,40,30,55,320,40,23,15,146,*47 ------------------------- Raw GPS | UTC time: '153938.0' | Longitude: '-120.668886' | Latitude: '35.258143' | Altitude: '46.100000' ------------------------- CDMA BS | Not available }}} Controlling the !ModemManager service: * Ubuntu 16.04 (use systemctl) {{{#!bash # stop ModemManager systemctl stop ModemManager # disable ModemManager at boot systemctl disable ModemManager # enable ModemManager at boot systemctl enable ModemManager # start ModemManager systemctl start ModemManager }}} Debugging with !ModemManager can be done by running !ModemManager with the '--debug' flag. For example, on Ubuntu 16.04: {{{#!bash # stop ModemManager systemctl stop ModemManager # run manually with debug ModemManager --debug --log-level=DEBUG # set logging level to max mmcli -G DEBUG # set logging level to minimum mmcli -G ERR # AT commands can be sent when in debug mode mmcli --modem 0 --timeout=120 --command="ATI" # Ident }}} References: * [https://www.freedesktop.org/software/ModemManager/man/latest/mmcli.8.html mmcli man page] * [https://docs.ubuntu.com/core/en/stacks/network/network-manager/docs/configure-cellular-connections Ubuntu Core - Configuring Cellular Connections] [=#networkmanager] === !NetworkManager === !NetworkManager is a package containing a background service/daemon and a command-line-interfalce (nmcli) that can be used to configure and connect network interfaces. It is often used in conjunction with !ModemManager for Cellular modems. Notes: - network-manager-1.2.6 (Ubuntu 16.04) has a different cmdline syntax for nmcli than network-manager-0.9.8.8 (Ubuntu 14.04). The following examples are for network-manager-1.2.6+ Example usage: - Show version: {{{#!bash root@ventana:~# nmcli --version nmcli tool, version 1.2.6 }}} - Show Device Status: {{{#!bash # show status root@ventana:~# nmcli device status DEVICE TYPE STATE CONNECTION eth0 ethernet connected Wired connection 1 cdc-wdm0 gsm disconnected -- eth1 ethernet unavailable -- can0 can unmanaged -- lo loopback unmanaged -- }}} - Bring down Wired Connection 1: {{{#!bash root@ventana:~# nmcli connection down id 'Wired connection 1' Connection 'Wired connection 1' successfully deactivated }}} - Add a modem: * Example: QMI controlled modem with an APN=h2g2 (Google Fi): {{{#!bash root@ventana:~# nmcli connection add type gsm ifname cdc-wdm0 con-name mymodem apn h2g2 Connection 'mymodem ' (6d89ff6e-6eb6-4f0f-80d1-fb081165f710) successfully added. }}} * Example: AT controlled modem with a Verizon Dynamic IP SIM: {{{#!bash root@ventana:~# nmcli connection add type gsm ifname ttyACM0 con-name mymodem apn vzwinternet Connection 'mymodem ' (6d89ff6e-6eb6-4f0f-80d1-fb081165f710) successfully added. }}} - Connect to mymodem device: {{{#!bash root@ventana:~# nmcli connection up id mymodem Connection successfully activated }}} Controlling the !NetworkManager service: * Ubuntu 16.04 (use systemctl) {{{#!bash # stop NetworkManager systemctl stop NetworkManager # disable NetworkManager at boot systemctl disable NetworkManager # enable NetworkManager at boot systemctl enable NetworkManager # start NetworkManager systemctl start NetworkManager }}} Troubleshooting: * if you find your modem's primary interface that !ModemManager detects is inconsistent you will want to remove the {{{interface-name=}}} line from the {{{[conneciton]}}} section of your modem configuration in the {{{/etc/NetworkManager/system-connections/}}} file for your modem and add a {{{device-id=}}} line to the {{{[gsm]}}} section that refers to the unique modem id string that !ModemManager defines for the modem shown on the 2nd line output from {{{mmcli -m 0}}}. You can also use dbus to get the {{{device-id}}} as such: {{{#!bash root@ventana:~# dbus-send --print-reply --system \ --dest=org.freedesktop.ModemManager1 \ /org/freedesktop/ModemManager1/Modem/0 \ org.freedesktop.DBus.Properties.Get \ string:org.freedesktop.ModemManager1.Modem string:DeviceIdentifier method return time=1504221807.956321 sender=:1.3 -> destination=:1.27 serial=41 reply_serial=2 variant string "ce4335fc20b8e7d2bf65f68483b79e78216e0256" }}} [=#building-from-source] === Building libqmi/libmbim/modemmanager from source === You can also build the latest modemmanager, libqmi, libmbim easily from source on an Ubuntu system. It is recommended to use stable releases which you can easily do from the PPA's provided above however if you wish to debug, contribute patches, or try patches from the various mailing lists you will need to build from the git repo sources. For example the following was done on Ubuntu 16.04 (xenial): * libqmi: {{{#!bash apt-get install build-essential git pkg-config automake autoconf intltool libtool gtk-doc-tools apt-get install libglib2.0-dev libgudev-1.0-dev git clone git://anongit.freedesktop.org/libqmi && cd libqmi && ./autogen.sh make make install ldconfig cd .. }}} - you can find the latest 'stable' release from https://www.freedesktop.org/software/libqmi/ (untar and run configure) * libmbim: {{{#!bash apt-get install build-essential git pkg-config automake autoconf intltool libtool gtk-doc-tools apt-get install libglib2.0-dev libgudev-1.0-dev git clone git://anongit.freedesktop.org/libmbim/libmbim && cd libmbim && ./autogen.sh make make install ldconfig cd .. }}} - you can find the latest 'stable' release from https://www.freedesktop.org/software/libmbim/ (untar and run configure) * modemmanager: {{{#!bash git clone git://anongit.freedesktop.org/ModemManager/ModemManager && cd ModemManager && ./autogen.sh make make install ldconfig cd .. }}} - you can find the latest 'stable' release from https://www.freedesktop.org/software/ModemManager/ (untar and run configure) Notes: - if you are building and installing from source you should remove all other packages that install libmbim or libqmi: {{{#!bash apt-get purge libmbim-glib-dev llibmbim-glib-doc libmbim-glib4 libmbim-glib4-dbg libmbim-proxy libmbim-utils apt-get purge libqmi-glib-dev libqmi-glib-doc libqmi-glib1 libqmi-glib1-dbg libqmi-proxy libqmi-utils }}} [=#troubleshooting] === Troubleshooting Modem support on Ubuntu === Because modem technology is constantly changing it is often best to try to get it working on the most modern Linux system possible with up to date kernel drivers and libraries. Often this is easily accomplished with Ubuntu under the following circumstances: - use the latest mainline Linux kernel if you can, otherwise use the most recent available Ubuntu kernel - use the latest !ModemManager, libqmi, and libmbim PPA's (see above) Use !ModemManager to see if your modem is detected and attempt connecting. Querying a modem with !ModemManager will also tell you what control interfaces exist and what type of control they use which is critical to understanding the requirements for your modem. ''' Recommended Tip ''' * Gateworks recommends connecting the modem and SIM to a Desktop or Laptop running Ubuntu Linux for isolated troubleshooting apart from the Gateworks hardware. To connect a Mini-PCIe modem to a desktop or laptop, please purchase a [#usbtominipcieadapter USB to Mini-PCIe adapter] from a third party like Amazon or Newegg, etc. Troubleshooting steps: * Determine what devices you have present and what drivers are being used to possibly support them: {{{#!bash root@ventana:~# lsusb Bus 001 Device 003: ID 1199:9071 Sierra Wireless, Inc. Bus 001 Device 002: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@ventana:~# dmesg | egrep -ie qualcom\|mbim\|sierra\|wdm [ 11.253539] usb 1-1.2: Product: Sierra Wireless MC7455 Qualcomm® Snapdragon™ X7 LTE-A [ 11.253546] usb 1-1.2: Manufacturer: Sierra Wireless, Incorporated [ 11.378483] usbcore: registered new interface driver cdc_wdm [ 11.395365] usbserial: USB Serial support registered for Qualcomm USB modem [ 11.397829] qcserial 1-1.2:1.0: Qualcomm USB modem converter detected [ 11.398318] usb 1-1.2: Qualcomm USB modem converter now attached to ttyUSB0 [ 11.400563] qcserial 1-1.2:1.2: Qualcomm USB modem converter detected [ 11.402218] usb 1-1.2: Qualcomm USB modem converter now attached to ttyUSB1 [ 11.404332] qcserial 1-1.2:1.3: Qualcomm USB modem converter detected [ 11.406082] usb 1-1.2: Qualcomm USB modem converter now attached to ttyUSB2 [ 11.408664] qmi_wwan 1-1.2:1.8: cdc-wdm0: USB WDM device [ 11.412510] qmi_wwan 1-1.2:1.10: cdc-wdm1: USB WDM device }}} - Note that the 'usbcore: registered' messages simply indicate a driver is loaded not that it has detected a supported device - if qmi_wwan detects your modem it speaks QMI (example above) - if cdc_mbim detects your modem it speaks MBIM - you can also look at what driver module is bound to a device (QMI example): {{{#!bash root@ventana:~# ls -l /sys/class/usbmisc/cdc-wdm0/device/driver/ | grep module lrwxrwxrwx 1 root root 0 Mar 7 22:20 module -> ../../../../module/qmi_wwan }}} * Use !ModemManager to see what ports and driver are detetcted/supported: {{{#!bash root@ventana:~# mmcli --modem 0 | grep -i -E ports\|driver | drivers: 'qmi_wwan, qcserial' | ports: 'ttyUSB0 (qcdm), ttyUSB2 (at), cdc-wdm0 (qmi), wwan0 (net), wwan1 (net), cdc-wdm1 (qmi)' }}} - here we see that the modem in the system is supported by the 'qcserial' driver and the 'qmi_wwan' driver, it speaks 'qcdm', 'at', and 'qmi' control protocols, and it uses the 'wwan0' network device for data * Check PIN status, power state, registration state, and signal quality by looking at the 'Numbers' and 'Status' section of !ModemManager output: {{{#!bash root@ventana:~# mmcli --modem 0 ... ------------------------- Numbers | own : '18052959083' ------------------------- Status | lock: 'sim-pin2' | unlock retries: 'sim-pin (3), sim-pin2 (10), sim-puk (10), sim-puk2 (10)' | state: 'registered' | power state: 'on' | access tech: 'umts' | signal quality: '31' (recent) ------------------------- Modes | supported: 'allowed: 2g, 3g, 4g; preferred: none' | current: 'allowed: 2g, 3g, 4g; preferred: none' ------------------------- ... }}} Getting help: - When asking for help make sure to provide the following details: * Modem make/model * Output of lsusb showing modem * Output of {{{mmcli --modem 0}}} to show detected modem details * Output of {{{dmesg | egrep -ie qualcom\|mbim\|sierra\|wdm}}} to show driver messages * Output of {{{uname -r}}} to show kernel version * Output of {{{qmicli --version}}} and {{{mbimcli --version}}} to show what versions you have - for QMI: post to libqmi-devel with details * Add Output of {{{qmicli --dms-get-{manufacturer,model,revision,capabilities} }}} - revision is firmware - capabilities shows if SIM is supported - capabilities shows networks - for MBIM: post to libmbim-devel with details [=#openwrt] == OpenWrt Cellular Modem Support == OpenWrt supports a wide range of cellular modems. Depending on the modem, a different software package / driver will be used: * [#comgtpackage comgt] : Most GSM / 3G modems : Uses AT commands through the {{{comgt}}} package. * [#uqmipackage uqmi] : Newer modems using Qualcomm chipsets : For modems that speak QMI (Quallcom MSM Interface) such as many of the 4G/LTE modems, use uqmi. [=#openwrt-comgt] === comgt package === The {{{comgt}}} package (http://comgt.sourceforge.net/) supports configuration of various cellular modems that use AT commands such as the Sierra Wireless, Novatel, and Option modems. This package supports startup scripts that are used for network interfaces specified with proto=3g. When a network interface is configured with proto=3g then the following things will occur when that interface is brought up (by virtue of {{{/lib/netifd/proto/3g.sh}}}): 1. the {{{gcom}}} app is used on the interface 'device' to determine what card is being used. Depending on the card and the service various AT commands may be sent for modem configuration. 2. the {{{chat}}} application application will run with a {{{chat}}} script (from {{{/etc/chatscripts}}}) which depends on the card type. This script is what connects to the network by using AT commands to specify the APN etc 3. The {{{pppd}}} daemon is run on the 'device' which creates a 'point to point' network interface (named 3g-) over the serial connection ==== Example configurations ==== UCI is a configuration system for OpenWrt. More information can be found [http://wiki.openwrt.org/doc/uci here] A modem must be configured in OpenWrt. The following uci properties are used by {{{comgt}}} and the 3g proto: * proto - must be 3g * device - the serial device (modem dependent) used for both data/control (used by {{{gcom}}}/{{{chat}}}/{{{pppd}}}). Consult the modem information below to determine what device to use for your modem * service - umts|cdma|evdo - the service type (which dictates the {{{chat}}} script used) * apn - the APN of your provider * pincode - the PIN (if required) to use your SIM Examples: * An example configuration for a Sierra Wireless MC9870 3G UMTS modem (ie AT&T Carrier using the ISP.CINGULAR APN): {{{#!bash uci set network.wan=interface uci set network.wan.proto=3g uci set network.wan.service=umts uci set network.wan.apn=ISP.CINGULAR uci set network.wan.device=/dev/ttyUSB4 uci commit network }}} * Note that UMTS/GSM providers sometimes require a user and password. In this case the ppp scripts require this information in your network interface. If your user is 'user' and password is 'pass' you can set this via: {{{#!bash uci set network.wan.username=user uci set network.wan.password=pass }}} * An example configuration for a Sierra Wireless MC5728 3G CDMA/EVDO modem (ie Sprint/Verizon Carriers): {{{#!bash uci set network.wan=interface uci set network.wan.proto=3g uci set network.wan.service=cdma uci set network.wan.device=/dev/ttyUSB0 uci commit network }}} * Note that CDMA/EVDO modules need to be 'activated' (one-time) before they can connect to he carrier's network. This is best done using the Windows software from the module vendor (For Verizon this is VZAccess Manager bundled with the CDMA Watcher drivers/application) * An example configuration for a Sierra Wireless MC9870 3G UMTS modem (ie AT&T Carrier using the ISP.CINGULAR APN): {{{#!bash uci set network.wan=interface uci set network.wan.proto=3g uci set network.wan.service=umts uci set network.wan.apn=ISP.CINGULAR uci set network.wan.device=/dev/ttyUSB4 uci commit network }}} * An example configuration for a Sierra Wireless MC7700 LTE/HSPA+ Gobi modem (ie AT&T Carrier using the ISP.CINGULAR APN): {{{#!bash uci set network.wan=interface uci set network.wan.proto=3g uci set network.wan.service=umts uci set network.wan.apn=ISP.CINGULAR uci set network.wan.device=/dev/ttyUSB3 uci commit network }}} * An example configuration for an Option Module: {{{#!bash uci set network.wan=interface uci set network.wan.proto=3g uci set network.wan.service=umts uci set network.wan.apn=ISP.CINGULAR uci set network.wan.device=/dev/ttyHS5 uci commit network }}} ==== Using {{{gcom}}} to see things like: modem info, SIM state, and signal strength ==== The {{{comgt}}} package has an application installed to {{{/usr/bin/gcom}}} that uses {{{chat}}} scripts installed in {{{/etc/gcom}}} to perform common tasks with supported 3G devices (assuming {{{/dev/ttyUSB3}}} is the control channel as in a MC8790): * report SIM status, connection status, and signal quality: {{{#!bash # gcom -d /dev/ttyUSB3 SIM ready Waiting for Registration..(120 sec max) Registered on Home network: "AT&T",2 Signal Quality: 12,99 }}} * for Option GTM671WFS (on ttyHS3) {{{#!bash # gcom -d /dev/ttyHS3 SIM ready Waiting for Registration..(120 sec max) Registered on Home network: "AT&T",2 Signal Quality: 17,99 }}} * report just signal strength: {{{#!bash # gcom -d /dev/ttyUSB3 sig Signal Quality: 12,99 }}} * report card info (mfg strings): {{{#!bash # gcom -d /dev/ttyUSB3 info ##### Wireless WAN Modem Configuration ##### Product text: ==== Manufacturer: Sierra Wireless, Inc. Model: MC8790 Revision: K1_0_2_8AP C:/WS/FW/K1_0_2_8AP/MSM6290/SRC 2008/09/17 14:00:22 IMEI: 352974021856935 IMEI SV: 3 FSN: D661380183210 3GPP Release 6 +GCAP: +CGSM,+DS,+ES OK ==== Manufacturer: Sierra Wireless, Inc. IMEI and Serial Number: 352974021856935 Manufacturer's Revision: K1_0_2_8AP C:/WS/FW/K1_0_2_8AP/MSM6290/SRC 2008/09/17 14:00: Hardware Revision: Network Locked: 0 Customisation: Band settings: ( ) APN: 1,"IP","ISP.CINGULAR","0.0.0.0",0,0 ##### END ##### }}} [=#uqmi] === uqmi package === Modems that speak the QMI protocol for configuration/connection require a driver such as qcserial that exposes the modem's serial interfaces, as well as the qmi_wwan driver, which exposes a network interface and a QMI interface, along with userspace tools that speak to the QMI interface. * qcserial driver exposes the modem's serial interfaces * qmi_wwan driver which exposes a network interface OpenWrt has a written the uqmi application from scratch which replaces the more bulky (~1.4MB) libqmi and also includes netifd protocol handler support (meaning you can use UCI for configuration). Known devices that use QMI (Note that some of these support both QMI or AT control via different firmware from Carriers): * Sierra Wireless MC77xx series * Sierra Wireless MC7354 OpenWrt Packages: * kmod-usb-serial-qualcomm - qcserial.ko * kmod-usb-net-qmi-wwan - qmi_wwan.ko * uqmi Notes: * There is no luci web-admin protocol support for QMI currently which means you cannot configure a QMI modem via the web-admin ==== Example QMI modem configurations ==== * An example configuration for a Sierra Wireless MC7354 modem configured for AT&T UMTS (which is the 2nd wwan device): {{{#!bash uci set network.wan=interface uci set network.wan.ifname=wwan1 uci set network.wan.proto=qmi uci set network.wan.apn=ISP.CINGULAR uci set network.wan.device=/dev/cdc-wdm1 uci set network.wan.delay=90 uci commit network }}} * The GSM/UMTS modem is the 2nd device ({{{/dev/wwan1}}}, {{{/dev/cdc/wdm1}}}) * This modem needed a 90 second delay before trying to connect * Example {{{/etc/config/network}}} content for uqmi modem {{{#!bash config interface 'wan' option ifname 'wwan1' option proto 'qmi' option apn 'ISP.CINGULAR' option device '/dev/cdc-wdm1' option delay '90' }}} ==== uqmi usage and troubleshooting ==== Examples: * Check SIM status: {{{#!bash root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-pin-status { "pin1_status": "disabled", "pin1_verify_tries": 3, "pin1_unblock_tries": 10, "pin2_status": "not_verified", "pin2_verify_tries": 10, "pin2_unblock_tries": 10 } }}} - if you see a 'UIM uninitialized' you have a SIM issue such as SIM not inserted * Check for available networks: {{{#!bash root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-serving-system { "registration": "registered", "plmn_mcc": 310, "plmn_mnc": 260, "plmn_description": "Project Fi", "roaming": false } }}} - above shows we are registered on the providers network (in this case Google Fi) * Check data status: {{{#!bash root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-data-status "connected" }}} * Get signal info: {{{#!bash root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-signal-info { "type": "hdr", "rssi": -125, "ecio": 5, "io": -106, "type": "wcdma", "rssi": -99, "ecio": 19 } }}} * Scan networks: {{{#!bash root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --network-scan { "network_info": [ { "mcc": 310, "mnc": 260, "description": "T-Mobile", "status": [ "available", "home", "not_forbidden", "preferred" ] }, { "mcc": 310, "mnc": 260, "description": "Project Fi", "status": [ "current_serving", "home", "not_forbidden", "preferred" ] }, { "mcc": 310, "mnc": 260, "description": "T-Mobile", "status": [ "available", "home", "not_forbidden", "preferred" ] }, { "mcc": 310, "mnc": 410, "description": "AT&T", "status": [ "available", "roaming", "not_forbidden", "not_preferred" ] }, { "mcc": 310, "mnc": 410, "description": "AT&T", "status": [ "available", "roaming", "not_forbidden", "not_preferred" ] }, { "mcc": 311, "mnc": 480, "description": "Verizon", "status": [ "available", "roaming", "forbidden", "not_preferred" ] }, { "mcc": 312, "mnc": 770, "description": "312-770", "status": [ "available", "roaming", "forbidden", "not_preferred" ] } ], "radio_access_technology": [ { "mcc": 310, "mnc": 260, "radio": "lte" }, { "mcc": 310, "mnc": 260, "radio": "umts" }, { "mcc": 310, "mnc": 260, "radio": "gsm" }, { "mcc": 310, "mnc": 410, "radio": "lte" }, { "mcc": 310, "mnc": 410, "radio": "umts" }, { "mcc": 311, "mnc": 480, "radio": "lte" }, { "mcc": 312, "mnc": 770, "radio": "lte" } ] } }}} * Get current IP settings: {{{#!bash root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-current-settings { "pdp-type": "ipv4", "ip-family": "ipv4", "mtu": 1430, "ipv4": { "ip": "25.232.251.49", "dns1": "10.177.0.34", "dns2": "10.177.0.210", "gateway": "25.232.251.50", "subnet": "255.255.255.252" }, "ipv6": { }, "domain-names": { } } }}} - note that some QMI modems use raw-ip and thus DHCP will not work. This command can be used to determine the IP settings provided by the provider If all is well, you will see your wwan interface with an IP address via ifconfig. If things don't work examine the logs to see what failed: {{{#!bash logread | grep qmi }}} You you see 'Unable to connect, check APN and authentication' in the log, then you either have an invalid APN or auth credentials or you need to increase the delay config parameter. [=#init-scripts] === Additional init scripts for some devices === Note that some devices require some additional manipulation to be used for cellular communications which the {{{comgt}}} scripts may not handle. In these cases you can create an init script to configure the device properly: * typically USB dongles, require the 'setmode' application to be used to switch the devices from a USB Mass Storage device configuration to a 3G modem configuration * some devices have AT commands that are required to take them out of low-power modes. For example, Sierra Wireless modems are shipped configured in low-power (airplane) mode. A startup script can be used to always set full power mode on bootup (Note: it appears this is just the way they are shipped - this setting is persistent so you should only need to set it once). The following shell commands will create an init script that will ensure a sierra wireless modem is taken out of 'Airplane' mode on bootup (assuming 'modem control' device is {{{/dev/ttyUSB3}}} - change appropriately for your device): {{{#!bash # set Modem data/control device in /etc/config/gpsd uci set network.wan.ctrl_device=/dev/ttyUSB3 uci commit # create an init script that enables full power on bootup for all 3g devices cat << EOF > /etc/init.d/3g_power_enable #!/bin/sh /etc/rc.common START=80 DEV=0 start(){ include /lib/network scan_interfaces local ifc for ifc in \$interfaces; do local proto config_get proto "\$ifc" proto [ "\$proto" == "3g" ] && { local device config_get device "\$ifc" ctrl_device [ "\$device" -a -c "\$device" ] && { logger -t "3g" "Enabling full power mode for \$device" echo -e -n "at+cfun=1\015" > \$device } } done } chmod +x /etc/init.d/3g_power_enable /etc/init.d/3g_power_enable enable }}} [[CollapsibleStart(OpenWrt LuCI WebAdmin for Cellular Cards)]] [=#luci] === LuCI Web-Admin Configuration for Cellular Cards === The following instructions detail how to configure a cellular card using the LuCI web-admin: 1. Access the board's web interface. For instructions: [wiki:OpenWrt/webadmin#AccessingtheWebInterface Accessing the Web Interface] 2. Go to the Network tab, then the Interfaces tab. [[Image(modem1.jpg,800px)]] 3. Click on "Add new interface..." at the bottom left of the screen. 4. Name the interface. Here it is named "wan" 5. Check "Custom Interface" with nothing entered in the text box. [[Image(modem2.jpg,800px)]] 6. Under the Protocol field, select "UMTS/3G from the drop down menu. 7. Continue to fill out the remaining fields. [[Image(modem3.jpg,800px)]] 8. Click on Save & Apply at the bottom right of the screen. 9. Reboot the board. The modem should be woken up from the {{{/etc/init.d/3g}}} script a few seconds after the board boots. [[Image(modem4.jpg,800px)]] [[CollapsibleEnd]] [=#usb-routing] == USB Routing Notes for Gateworks products == Some of the Gateworks boards have options to physically route USB signals to either front-panel connectors (the default configured by the bootloader and/or kernel) or a PCI slot for use with a PCI-to-PCIe carrier for PCIe USB products like cellular modems. Please refer to the [wiki:USB#usb-devices Gateworks USB Device Table] and [wiki:USB#steering USB Steering] pages for details for each board. [=#sms] == Sending a SMS / Text Message == Depending on the carrier and plan, SMS messages can be sent from Gateworks boards via a Cellular Modem. Gateworks has tested and verify this works sending to a normal handset. The example shown is using AT commands which could be turned into a script if desired. 1. Connect to the modem where you can send AT commands. For AT Command instructions, see here: [#ATCommands AT Commands] 2. Verify that your modem supports SMS messages by typing the following AT command. If you see '''+CMGF: (0-1)''' then it is supported. {{{#!bash at+cmgf=? +CMGF: (0-1) OK }}} 3. Switch the modem into SMS Message Sending mode: {{{#!bash AT+CMGF=1 OK }}} 4. Enter the cellular number to send the SMS to as well as the message: {{{#!bash AT+CMGW="0661326109" > This is a test message from a Gateworks Single Board Computer sending SMS. > # hit ctrl+z to end SMS here +CMGW: 9 }}} 5. Note that after hitting ctrl+z CMGW shows a numerical number. This number is the ID of the SMS to be sent. 6. Send the SMS message with the following command, where the number matches the ID from Step 4&5 {{{#!bash AT+CMSS=9 OK }}} 7. OK Should appear after hitting enter for the send command. If ok appears, please check receiving handset. The 'from' number will be from whatever number is registered with the SIM. == Specific Modem Notes == [=#ublox] === U-Blox Modems === ==== Toby L2 ==== Gateworks has tested the Toby MPCI-L201 in USA (Mini-PCIe form factor) [https://www.u-blox.com/en/product/mpci-l2-series] * LTE Cat 4 - Up to 150Mb/s throughput * Multiple countries supported with different model variants * Industrial Temperature -40 to +85C Operation * FOTA Support * Drivers required * cdc_acm driver provides ttyACM0(at) (/dev/ttyACM0) * rndis_host driver provides usb0(net) * Will create a network interface shown from the command: ifconfig -a * No pinout concerns - PERST# and WLAN_DIS# are used and are 3.3V compliant, VDD is 3.0 to 3.6V * Available on Digikey (typically in stock): [https://www.digikey.com/products/en?keywords=MPCI-L201] * Toby L2 Documentation: [https://www.u-blox.com/en/product-resources?f%5B0%5D=property_file_product_filter%3A2451] '''Ubuntu Notes:''' * Tested on [wiki:ventana/ubuntu Gateworks Xenial and Bionic] (Bionic requires installing network-manager) * Uses modem manager and network manager * Sample set of commands: {{{ mmcli --modem 0 --enable mmcli --modem 0 --simple-connect="apn=yourapnname" dhclient usb0 }}} * There will be an IP address assigned, something such as 192.168.1.100 to usb0. Test this using the ifconfig command (do not expect a WAN IP) * Try first to ping an actual IP address, like 8.8.8.8 (in case DNS isn't working....) * Then try a domain name, like www.yahoo.com * If a domain name doesn't work, try adding a DNS like the Google DNS as follows and try the ping again: {{{ echo "nameserver 8.8.8.8" > /etc/resolv.conf }}} '''OpenWrt Notes:''' * OpenWrt 16.02 and 18.02 have been tested * OpenWrt will show both usb0 and usb1 enumerated. usb1 should be used for the internet. * Must set the APN via AT commands (Read more in the [https://www.u-blox.com/sites/default/files/u-blox-CEL_ATCommands_%28UBX-13002752%29.pdf AT Command Manual]) * Sample AT Command set (login to modem AT commands on /dev/ttyACM0 with information [#at here]) {{{ AT+CFUN=4 # command to detach the module from the network AT+UCGDFLT=1,"IP","yourapn" # Initial PDP (packet data protocol) context configuration AT+CFUN=1 # return to the module full functionality }}} * AT+CGDCONT - Defines the connection parameters for a PDP context * AT+UCGDFLT - Configures the initial PDP context, i.e. sets the configuration of the PDN (packet data network) activated at attach time in LTE network. The configuration can be optionally saved in NVM (non volatile memory). * Tested configuration in /etc/config/network: {{{ config interface 'wan' option ifname 'usb1' option proto 'dhcp' }}} [=#sierra-wireless] === Sierra Wireless Modems === ''' ****Please check with Sierra Wireless for availability and EOL status **** ''' === Nimbelink NL-SW-LTE-TSVG / Telit LE910-SVG === *** Still in testing, contact support@gateworks.com *** * Details * 4G LTE CAT 3 * Pre-Certified Verizon Modem * 100Mbps download and 50Mbps upload speeds * Carriers * USA : Verizon * USB ID 1bc7:1201 Telit Wireless Solutions Drivers: * option.ko (CONFIG_USB_SERIAL_OPTION) exposes 5 serial ports: * {{{/dev/ttyUSB0}}} - qcdm * {{{/dev/ttyUSB1}}} - at * {{{/dev/ttyUSB2}}} - * {{{/dev/ttyUSB3}}} - at * {{{/dev/ttyUSB4}}} - * qmi_wwan (USB_NET_QMI_WWAN) exposes network interface and QMI interface: * {{{/dev/cdc-wdm0}}} - control (QMI) Links: Nimbelink Module *[http://nimbelink.com/skywire-cellular-modem-lte/] Mini-PCIe Carrier Board for Nimbelink Module *[https://www.bipom.com/products/us/4382536.html] [=#troubleshooting] == Troubleshooting == Here are some troubleshooting tips with regards to cellular modems: * Make sure your modem is being recognized on the USB bus with {{{lsusb}}} - if not, check that the USB bus is correctly steered to the miniPCIe socket the modem is installed in (see the [wiki:USB#steering USB Steering] wiki page) - make sure the modem supports USB 2.0 - check the modem pinout and ensure that it is compatible with PCIe signalling if used on a miniPCIe socket with PCIe (Sierra Wireless -V modems can not have the PERST# signal at 3p3V - see [#vaux1 here]) * Does your modem require a driver or driver update that is not available in the Linux kernel version you are using? - a {{{lsusb}}} will show the Vendor ID and Product ID of your device which typically need to match known ID's in drivers (some newer devices match USB class ID's and are more forgiving) - look at the kernel messages from the {{{dmesg}}} command for messages that might indicate a modem is not supported or lack of a known driver supporting that device. Most modem drivers will create a number of 'tty' devices in /dev/tty* - if you see no messages about this you may be missing driver support. * Make sure no other processes are interacting with your M2M device communication ports (ie mis-configured {{{gpsd}}}) * Is your GSM module locked to a Carrier/Network/SIM/PIN? - if so you have to unlock it (if possible/allowed) * Is your module in low-power / airplane mode? * Can you not send AT commands to a card? Try hotswapping the card * Is your modem a Sierra Wireless *-V modem with Voice audio capabilities? See [#vaux1 below] * Have you specified the correct APN for your GSM module? - Your carrier can provide you with the proper APN * Are you using the correct serial device? - most modules provide several, not all of which can be used with {{{pppd}}}/{{{chat}}}/{{{gcom}}} * Is your CDMA/EVDO module 'activated'? - you may need to do this on a Windows system with vendor-supplied application/drivers * Issue a reset command to the card when starting up (varies by card) {{{#!bash [ -e /dev/ttyUSBX ] && echo -e -n "AT~RESET\015" > /dev/ttyUSBX }}} For low level troubleshooting it may be useful to use a serial comm program (such as {{{screen}}}) to connect to the M2M device control port and issue AT commands directly: * AT+CREG? will return your network registration state: 0 - registered to home network, 1 - roaming, -1 not registered * AT+COPS? will return the operator selection: [,, See http://ernstagn.home.xs4all.nl/GPRS-HOWTO/GPRS-HOWTO.html for more info General Reference: * AT Commands (Note GSM 07.07, GSM 07.05, V.25ter and T.32 specifications can be obtained from http://www.etsi.org or http://www.3gpp.org) * [[http://www.sierrawireless.com/Support/Downloads/AirPrime/SL_Series/~/media/Support_Downloads/AirPrime/Software/2130617%20AirCard-AirPrime%20Supported%20AT%20Commands%20v4.ashx AT Command Reference for AirCard-AirPrime Modems]] * http://www.canarysystems.com/nsupport/CDMA_AT_Commands.pdf [=#at] === AT Commands === Many cellular modems use AT commands for control. Examples shown on this page are a quick and easy way to issue commands, however, no responses can be seen. While many model and brands use similar AT commands you need to contact the modem vendor or search the Internet for a complete list for that particular brand and model. To get to a console where AT commands and their responses can be seen, a serial program needs to be used, such as minicom or screen. For AT commands, the correct port must be used. It will be one of the enumerated ports such as {{{/dev/ttyUSB0}}}, {{{/dev/ttyUSB1}}}, {{{/dev/ttyUSB2}}}, {{{/dev/ttyUSB3}}}, etc {{{#!bash screen /dev/ttyUSB3 }}} This will open a window where one can start typing AT commands. Example shown below: {{{#!bash at+cgmi Sierra Wireless, Incorporated OK at+cgmm MC7700 OK at+csq ERROR }}} To send AT Commands from the Linux Shell, use echo with -e -n and terminate with \015. Example below: {{{#!bash echo -e -n "at+cfun=1\015" > /dev/ttyUSB3 }}} [=#reset-via-at] ==== Resetting a Modem with AT Commands ==== The following AT commands can be used to perform a soft reset on particular modems: * ZTE: {{{#!bash AT+ZRST }}} * Sierra Wireless: {{{#!bash AT!RESET }}} or {{{#!bash AT+CFUN=1,1 }}} * Huawei and others: {{{#!bash AT+CFUN=4 AT+CFUN=6 }}} Consult your modem documentation for AT commands for that device and firmware. [=#reset-sim] === Reset for SIM Read === Most Modem firmware will only check a SIM on power-up. If a SIM is activated or inserted after the cellular card is powered, the cellular may need to be re-powered or re-initialized to recognize the SIM. While each modem likely has a unique way to do this via an AT command, a QMI command, or an MBIM command resetting the modem is always another option. Refer to the [wiki:USB#reset USB reset] wiki page for details on how to do this on various boards and miniPCIe sockets. [=#testing] === Testing a Connection === A quick way to verify the module has connected up to the cellular carrier and has received an IP address is to run the ifconfig command from the Linux console. The following is an example output, note the 3g-wan entry, this will not show up if a connection has not been established. In this example 32.177.140.183 is the IP address. Once a connection is established, you should also be able to ping to the internet. {{{#!bash root@OpenWrt:/# ifconfig 3g-wan Link encap:Point-to-Point Protocol inet addr:32.177.140.183 P-t-P:10.64.64.64 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:70 errors:0 dropped:0 overruns:0 frame:0 TX packets:72 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:5842 (5.7 KiB) TX bytes:5000 (4.8 KiB) br-lan Link encap:Ethernet HWaddr 00:0C:E3:70:DA:17 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20c:e3ff:fe70:da17/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:408 (408.0 B) eth0 Link encap:Ethernet HWaddr 00:D0:12:56:EE:6A UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:2 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:168 (168.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:61 errors:0 dropped:0 overruns:0 frame:0 TX packets:61 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6044 (5.9 KiB) TX bytes:6044 (5.9 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 00-0C-E3-70-DA-17-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:145 (145.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 00:0C:E3:70:DA:17 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:772 (772.0 B) root@OpenWrt:/# ping google.com PING google.com (74.125.224.71): 56 data bytes 64 bytes from 74.125.224.71: seq=0 ttl=51 time=176.596 ms 64 bytes from 74.125.224.71: seq=1 ttl=51 time=166.074 ms 64 bytes from 74.125.224.71: seq=2 ttl=51 time=155.902 ms ^C --- google.com ping statistics --- 3 packets transmitted, 3 packets received, 0% packet loss round-trip min/avg/max = 155.902/166.190/176.596 ms }}} [=#sim] == SIM Card use on PCI Express form-factor modems == PCI Express form-factor GSM Modems require SIM (Subscriber Identity Module) cards in order to connect to the providers network. There are several different methods for accessing SIM cards depending on hardware: * Some modems have a SIM slot on them * Others use sideband signals on the PCIe connector that route to an external SIM slot: * The [http://shop.gateworks.com/index.php?route=product/product&product_id=146&search=gw16103=GW16103 GW16103] Mini-PCIe SIM, uSD and USB expansion board can be used to provide SIM support for boards with Mini-PCIe sockets. * The [#GW17005Instructions GW16038/GW16062] carriers can be used in specific slots of the Gateworks Laguna product families. [[CollapsibleStart(MiniPCI Information)]] === MiniPCI to Mini-PCIe Multiple SIM Card Access === Gateworks has several mini-PCI to PCI Express Mini Card adapters specifically designed for PCI Express Mini Card Standard GSM/GPRS/EDGE/UMTS/HSPA wireless radio modules on the Laguna platforms: * [http://shop.gateworks.com/index.php?route=product/search&search=GW16049 GW16049] - USB routed, No SIM connectors (Can't be used for GSM Modules) * [http://shop.gateworks.com/index.php?route=product/search&search=GW16038 GW16038] - USB routed, has SIM connectors * [http://shop.gateworks.com/index.php?route=product/search&search=GW16059 GW16059] - PCIe and USB routed, No SIM connectors (Can't be used for GSM Modules) * [http://shop.gateworks.com/index.php?route=product/search&search=GW16062 GW16062] - PCIe and USB routed, has SIM connectors * [http://shop.gateworks.com/index.php?route=product/search&search=GW17005 GW17005] - SIM carrier for cellular cards without SIM or boards with PCIe slots (ie. GW2380, GW23882, GW2383, GW2391) The GW16038/GW16062 carriers have 3 SIM connector sites (labeled USIMA, USIMB, USIMC) which can be selected depending on jumper position and software controlled GPIO steering. Jumper block W1 can set SEL0/SEL1 signals low/high or GPIO controlled. The card selection is shown in a table on the PCB silkscreen. You can set the jumpers to a specific SIM connector or allow 2 GPIO signals from the baseboard to select the location (useful for example in a product that needs to select a specific SIM based on other criteria such as geographic location). Note that the GSMSEL0 and GSMSEL1 GPIO's differ per board which can be found in the board's User Manual but are summarized here for convenience: * Laguna GW2388-x (Bottom MiniPCI socket J4): * GPIO7 - GSMSEL0 * GPIO8 - GSMSEL1 * Laguna 2382 * Turn on USB by enabling GPIO10 as noted in the troubleshooting section above [#Troubleshooting:] Examples: * Laguna GW2388 using bottom-right miniPCI socket for GSM radio - select SIM site: {{{#!bash echo 1 > /sys/class/gpio/gpio7/value; echo 1 > /sys/class/gpio/gpio8/value ;# sel SELE1/SEL0 1,1 for SIMC echo 1 > /sys/class/gpio/gpio7/value; echo 0 > /sys/class/gpio/gpio8/value ;# sel SELE1/SEL0 1,0 for SIMB echo 0 > /sys/class/gpio/gpio7/value; echo 1 > /sys/class/gpio/gpio8/value ;# sel SELE1/SEL0 0,1 for SIMA echo 0 > /sys/class/gpio/gpio7/value; echo 0 > /sys/class/gpio/gpio8/value ;# sel SELE1/SEL0 0,0 for None }}} Images: * GW16062 showing SIM card insertion [[Image(16062.JPG,400px)]] * GW16038 showing SIM card selection jumper block [[Image(20131029_083627.jpg,400px)]] [[CollapsibleEnd]] == Other Helpful Links == * [http://m2msupport.net/m2msupport/search-page/?Form!Factor=PCIe A M2M site for looking at modems] * [http://www.att.com/edo/mmt/matching-tools-form.jsp AT&T Module Picker] * [http://ei.att.com/modules/ATT_Approved_3G_4G_Modules.xlsx AT&T Reference Sheet] [=#usbtominipcieadapter] = USB to Mini-PCIe Modem Adapters = These can be very useful for debugging with a desktop or laptop. They can be acquired from third parties such as Amazon, Newegg, etc Be mindful to look to see if the adapter also has a SIM slot. [[Image(usbtominipcietop.jpg,600px)]] [[Image(usbtominipciebottom.jpg,600px)]]