wiki:newport/bootloader

Context Navigation

Version 7 (modified by Ryan Erbstoesser, 6 years ago) ( diff )
update hwconfig to use pci instead of pcie to match bootloader code

Newport U-Boot Bootloader

Newport U-Boot Bootloader

Gateworks supports the U-Boot Bootloader for the Newport product family. We provide pre-built firmware images (see here) as well as source for building and/or modifying it yourself.

One of the primary features of the Bootloader is to provide access to the hwconfig environment variable that the firmware uses for initial board configuration on power-up.

Pre-Built U-Boot Firmware

Pre-Built U-Boot is contained inside of the Gateworks Newport boot firmware artifact here: http://dev.gateworks.com/newport/boot_firmware/

Version

As of Q3, 2018, the U-Boot version used on the Newport boards is v2017.09-rc1

Source code is located here: https://github.com/Gateworks/uboot-newport

hwconfig

The U-Boot Bootloader by convention provides a hwconfig environment variable which is used by the boot firmware (before U-Boot is loaded and executed) to configure board options at power-up. These options can include things such as:

miniPCIe socket functions (ie PCIe vs mSATA vs USB3.0)
serial configuration (ie RS232 vs RS485)

hwconfig: miniPCIe Socket Configuration

Newport board model socket options:

GW630x:
- J9: PCIe
- J10: PCIe or SATA
- J11: PCIe or USB3.0
GW640x:
- J9: PCIe
- J10: PCIe or SATA
- J11: PCIe
- J12: USB 3.0 / SIM (no hwconfig)

Note that USB2.0 is routed to all three miniPCIe sockets always but as USB3.0 shares signals with PCIe you must choose between PCIe and USB3 on sockets that support USB3.

You can get/set the hwconfig variable within the U-Boot bootloader but you must reboot the board for it to take effect as the variable is acted upon in the Secondary Program Loader (SPL).

Examples:

Note that setting hwconfig currently requires saveenv to be ran twice

GW630x:

J10 PCIe, J11 PCIe (default)

setenv hwconfig 'j10:pci;j11:pci'; saveenv; saveenv

J10 mSATA, J11 USB3.0

setenv hwconfig 'j10:sata;j11:usb3'; saveenv; saveenv

J9/J10 disabled, J11 PCIe

setenv hwconfig 'j9:disabled;j10:disabled;j11:pci'; saveenv; saveenv

You can see that the hwconfig configuration took place by watching the output of the BDK during boot. For example:

Gateworks Newport SPL (3442703 Wed Jun 6 20:26:30 UTC 2018)

GSC     : v52 0xbf2d WDT:disabled board temp:38C
RTC     : 506646
Model   : GW6304-C
MFGDate : 03-28-2018
Serial  : 776375
DTB     : gw6304.dtb
SoC     : CN8030-1500BG676-SCP-P12-G 1024KB 1500/550MHz 0xa2 Pass 1.2
MMC0    : eMMC
MMC1    : not detected
Boot    : eMMC non-trusted
DRAM    : 2048 MB, 1333 MT/s, DDR4 UDIMM
J9      : PCI
J10     : SATA
J11     : USB3
QLM0    : PCIE_1X1@5000MHz
QLM1    : SGMII_1X1@1250MHz
QLM2    : DISABLED@5000MHz
QLM3    : SATA_2X1@6000MHz
Serial  : 2x RS232 without flow control
...
Hit any key to stop autoboot:  0
GW6304-C> print hwconfig
hwconfig=j10:sata;j11:usb3

The above shows that J9 is configured for PCI, J10 for SATA, and J11 for USB3

Note that hwconfig is also used for serial configuration so care should be taken to preserve that configuration if used

hwconfig: serial Configuration

Many boards in the Newport product family provide a 5-pin off-board serial connector that provides the following options:

1x RS485 FD (UART2)
1x RS485 HD (UART2)
1x RS232 w/ hardware flow control (UART2)
2x RS232 w/o hardware flow control (UART2/UART3)

By default 2x RS232 with no flow control is enabled. To configure a different option use the hwconfig U-Boot env variable. The mode property of the serial option defines the initial configuration of the serial port(s). If RS485 is selected by the mode property the term property will select whether or not on-board termination is enabled.

The mode property can have the following values:

rs232 - 2x RS232 (UART2/UART3) without hardware flow control (default if not specified)
rs232_dtr - RS232 (UART2) with hardware flow control
rs485_hd - RS485 half-duplex
rs485_fd - RS485 full-duplex

Examples:

Note that setting hwconfig currently requires saveenv to be ran twice

Enable RS485 half duplex no on-board termination

setenv hwconfig "serial:mode=rs485_hd,term=no"; saveenv; saveenv

Enable RS485 full duplex with on-board termination

setenv hwconfig "serial:mode=rs485_fd,term=yes"; saveenv; saveenv

Enable RS232 with hardware flow-control:

setenv hwconfig "serial:mode=rs232_dtr"; saveenv; saveenv

Note that hwconfig is also used for pcie configuration so care should be taken to preserve that configuration if used

Distro Config

The Newport Bootloader uses U-Boot's 'Distro Config' which is a well defined U-Boot env intended to make it easier for distro maintainers to develop compatible bootscripts. This primarily entails a set of 'boot scripts' and variables that control them.

Ultimately this U-Boot environment is looking for a U-Boot boot script on a 'bootable' partition (partitions with the 'boot' flag enabled). It searches in this order with these rules:

boot_targets - list of target device type/nums to search: defaults to mmc0 mmc1 usb0 sata0
devplist - dynamically created list of all partitions flagged as 'bootable'
boot_prefixes - list of directories within a partition searched for bootscripts
boot_scripts - list of boot script names searched for

Boot Scripts

When writing bootscripts compatible with Distro Config you can assume the following env variables:

devtype - the device type the script was loaded from (mmc|usb|sata)
devnum - the device number the script was loaded from (ie 0 for mmc0, 1 for mmc1, etc)
distro_bootpart - the partition number the script was loaded from (ie 0, 1, etc)
fdtcontroladdr - the address the device-tree is at (Note that the Newport bootloader does not load/manipulate the device-tree itself - this is done by the SPL which loads/manipulates the device-tree and passes it to the bootloader)
kernel_addr_r - address where kernel can be loaded
bootargs - default bootargs to pass to the kernel - you probably want to add to this and not overwrite it
console - the serial console device to pass to the kernel

Additionally you should note the following:

use load/ls/save commands which support FAT/ext filesystem types automatically instead of the fs specific commands
if using a root filesystem that is not supported by the bootloader (ie F2FS or BTRFS) you can place your kernel image in the FAT12 filesystem on partition 1 of the boot device. This filesystem is part of the 16MB 'Boot Firmware' image. If doing so you will need to compress the kernel and package it into a FIT image in order to fit it in the available space.

The Distro-Config environment supports legacy uImage scripts (it does not support FIT images with scripts). You can create these with the mkimage tool from U-Boot as such:

mkimage -A arm64 -T script -C none -d ubuntu.txt newport.scr

You can then place the uImage newport.scr on a bootable partition such as the embedded FAT12 filesystem within the Newport boot firmware as such:

fatfs-tool -i firmware-newport.img cp newport.scr /

Alternatively this can be done at runtime on the target within Linux by mounting the FAT12 partition. For example:

mount /dev/mmcblk0p1 /mnt
mkimage -A arm64 -T script -C none -d ubuntu.txt /mnt/newport.scr
umount

Boot Device Order (boot_targets)

While the Newport product family can only boot its Boot Firmware from an MMC device (ie eMMC or microSD), once you are booted to the bootloader you can choose from a wider variety of devices to boot the OS from.

This OS boot device order is specified by the Distro Config environment. Specifically it is controlled by the boot_targets env variable which defaults to mmc0 mmc1 usb0 sata0.

For example, to limit OS booting to only SATA:

setenv boot_targets sata0
saveenv

Flattened Image Tree (FIT) images

The U-Boot bootloader supports Flattened Image Tree (FIT) images which expand greatly on the legacy U-Boot image (uImage) format by allowing multiple binary blobs within an image. These blobs can be kernel images, ramdisk images, device-tree blobs, and bootloader scripts. Each image can also be optionally compressed (meaning U-Boot will decompress it) and check-sumed with a variety of hash mechanisms (meaning U-Boot will verify the image before using it).

Quick summary of FIT Images:

introduced to resolve limitations with original single-image formats and follow-on multi-image format supported by UBoot bootm (boot memory)
uses power of the Device-Tree-Compiler (DTC)
FIT .itb files can be created with mkimage by passing in a .its file which in device-tree notation describes the images
U-Boot supports FIT with several commands:
- source <addr>:<name> # source a script by name from FIT image in memory
- iminfo <fitaddress> # print all the info contained in a FIT image in memory and verify (just not boot it)
- imextract <fitaddress> <item> <addr> # extract item (ie kernel@1) to addr
- bootm <fitaddress>[#conf] - $fdtcontroladdr # boot default or 'conf' configuration (ie #config@1)
- bootm start <fitaddress>[#conf] - $fdtcontroladdr # boot from memory a specific configuration (or default configuration) from FIT image

Example:

kernel.its with a single compressed kernel for ARM64 (used by Newport)

/dts-v1/;
/ {
        description = "Simple image with single Linux kernel";
        #address-cells = <1>;
        images {
                kernel@1 {
                        description = "ThunderX kernel";
                        data = /incbin/("./Image.gz");
                        type = "kernel";
                        arch = "arm64";
                        os = "linux";
                        compression = "gzip";
                        load = <0x40080000>;
                        entry = <0x40080000>;
                        hash@1 {
                                algo = "sha256";
                        };
                };
        };

        configurations {
                default = "conf@1";
                conf@1 {
                        description = "Boot Linux kernel";
                        kernel = "kernel@1";
                };
        };
};

create image:

cp arch/arm64/boot/Image .
gzip Image
mkimage -f kernel.its /tftpboot/kernel.itb

boot the default configuration from U-Boot:

tftpboot $loadaddr kernel.itb && setenv bootargs 'console=ttyAMA0,115200n8 earlycon=pl011,0x87e028000000 coherent_poll=64M root=/dev/mmcblk2 rootfstype=f2fs' && bootm $loadaddr - $fdtcontroladdr

References:

Note: See TracWiki for help on using the wiki.

Download in other formats:

Plain Text