Kali

Offical Kali Linux images are now provided by ​Offensive Security for both Ventana and Newport.

Build-scripts can be found here:

• ​Ventana
• ​Newport
• Create your own - ​kali-linux-arm-chroot

The Ventana prebuilt image can be downloaded from ​here, ARM images > Gateworks.

Note: Offical images use Gateworks kernel repos.

What is Kali

Kali Linux (formerly known as BackTrack Linux) is an open-source, Debian-based Linux distribution aimed at advanced Penetration Testing and Security Auditing. Kali Linux contains several hundred tools targeted towards various information security tasks, such as Penetration Testing, Security Research, Computer Forensics and Reverse Engineering. Kali Linux is a multi platform solution, accessible and freely available to information security professionals.

Kali Linux was initially released on the 13th March 2013 as a complete, top-to-bottom rebuild of BackTrack Linux, adhering completely to Debian development standards.

Reference: ​https://www.kali.org/docs/introduction/what-is-kali-linux/

Kali on Gateworks

Official instructions:

• ​Official Page

The following instructions can be used on Ventana or Newport family boards.

Requirements:

• 16GB SD card or larger (Class 10 recommended)
• Gateworks SBC Ventana or Newport
• Linux Desktop Workstation
• Wireless radio capable of packet injection (Alfa AWPCIE-AX200U recommended)
• Antennas

Installing Kali to an SD card

Insert SD card into Linux workstation, use "dmesg" to check the device name udev has assigned, for example "/dev/sdb".

Some operating systems will auto-mount block storage devices, the partitions must be unmounted in order to write directly to the volume:

umount /dev/sdb?

Write image to SD card:

xzcat kali-linux-1-newport.img.xz |sudo dd of=/dev/sdb bs=4M status=progress

The card is now imaged with Kali. Because the partitions have already been unmounted simply remove the card.

Booting the SD card

To boot from the SD card on the Gateworks "boot_targets", or "bootdevs" need to be set so the SD card has priority over the flash.

Break out in the bootloader:

For Newport:

GW6204-B> setenv boot_targets mmc1 mmc0 usb0 scsi0
GW6204-B> saveenv

For Ventana:

Ventana > setenv bootdevs mmc
Ventana > print bootdevs     
bootdevs=mmc
Ventana > saveenv
Saving Environment to NAND...
Erasing NAND...
Erasing at 0x1000000 -- 100% complete.
Writing to NAND... OK
Ventana > 

Reboot the SBC.

Once Kali is loaded login, username "kali", password "kali".

Verify that your network interfaces are available:

ls /sys/class/net

Check your radio is capable of working on the channels that will be monitored:

iw phy phy0 channels

Install Metasploit Framework

Metasploit framework is an open source tool which can be used to probe systematic vulnerabilities on networks and servers.

Metasplot features:

• Command shell payloads that enable users to run scripts or random commands on a host
• Dynamic payloads that allow testers to generate unique payloads
• Meterpreter payloads that allow users to VMC and monitor sessions and upload and download files
• Static payloads that enables port forwarding and communications between networks

Offensive-Security offers a free online course for learning Metasploit: ​https://www.offensive-security.com/metasploit-unleashed/

To install Metasploit on Gateworks:

1. Update your system

   apt-get update 
   

2. Install curl

   sudo apt-get install curl -y 
   

3. Download and install Metasploit

   curl https://raw.githubusercontent.com/rapid7/metasploit-omnibus/master/config/templates/metasploit-framework-wrappers/msfupdate.erb > msfinstall && \
     chmod 755 msfinstall && \
     ./msfinstall
   

Aircrack-ng

Aircrack-ng is a suite of tools that can be used to access a WiFi networks security.

It focuses on different areas of WiFi security:

• Monitoring: Packet capture and export of data to text files
• Attacking: Replay attacks, deauthentication, fake access points and others via packet injection
• Testing: Checking WiFi cards and driver capabilities (capture and injection)
• Cracking: WEP and WPA PSK (WPA 1 and 2)

Reference: ​https://www.aircrack-ng.org/

For deauthentication the wifi adapter will need to be capable of packet injection.

To test if packet injection is available:

sudo aireplay-ng --test wlan0mon

Capturing packets

In order to capture packets airmon-ng is used to create a monitor interface.

To begin connect to the board using SSH (this is important later).

Kill processes that may interfere with airmon-ng:

sudo airmon-ng check kill

Start the monitor interface:

sudo airmon-ng start wlan0 #this command creates the "mon" interface "wlan0mon".

Start airodump-ng to begin capturing packets. Note, airodump-ng by default will only monitor on 2.4Ghz, use the "--band a" switch to enable 5ghz monitoring.

sudo airodump-ng --band a wlan0mon

Penetration testing your wifi network

Once the SSID you wish to test has been identified, record its MAC address and note which channel it's on. Single out that network to find clients which can be deauthenticated. In this example my BSSID is 11:22:33:44:55:66 on channel 44. We will create a log file to record the handshake called "my-handshake".

sudo airodump-ng -c44 --write my-handshake --bssid 11:22:33:44:55:66 wlan0mon

Run this scan until a client (station) is identified. For this example I've used my cell phone MAC 77:88:99:AA:BB:CC.

Start a new SSH session, so both sessions are open simultaneously.

In the second session execute your deauthentication attack (this is where packet injection is used):

Note: Do not deauthenticate devices which are not part of your network

sudo aireplay-ng --deauth 0 -a 11:22:33:44:55:66 -c 77:88:99:AA:BB:CC wlan0mon

Upon success the client is disconnected from the access point. When the client reconnects airodump-ng will capture the handshake and log it to the designated file.

Upper right displays handshake hash (pixelated in this image).

Wordlists and Aircrack-ng

Wordlists with default manufacturer passwords are provided by Metasploit framework. More wordlists can be found in "/usr/share/wordlists". A wordlist is only one potential approach to breaking the handshake hash. Though this is an excellent test to perform in order to verify your passwords aren't easily compromised.

An all around (basic) word list included with Kali is rockyou.txt.

sudo gunzip /usr/share/wordlists/rockyou.txt.gz #extract the wordlist
cat /usr/share/wordlists/rockyou.txt #display words contained in the list

Start aircrack-ng to decrypt the hash:

aircrack-ng my-handshake-01.cap -w /usr/share/wordlists/rockyou.txt

Getting help with Kali

Please direct all Kali Linux related questions to the forums:

​https://forums.kali.org/

Feel welcome to contact support@gateworks.com for questions specific to Gateworks.