| Version 1 (modified by , 7 years ago) ( diff ) |
|---|
Capturing Console Log
Console log: Copy and Paste of the serial console activity from a Gateworks Board.
This is very helpful to allow Gateworks to help customers debug issues.
Console log should include:
- Complete console activity from power on (start with board powered off, setup serial console , then power the board) - This will show the serial console with the U-Boot information
- The final command prompt once the board has completely finished booting
- Any errors, etc encountered thereafter.
For Example,
This example is very long but please note the following mandatory parameters:
U-Boot 2013.07-00012-g88e0a40 (Sep 25 2013 - 13:36:02)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
APP_IMAGE: Primary
Env: SPI FLASH
BOOT_CFG: SPI NOR 0x18000030
Gateworks Corporation Copyright 2013
Model: GW5400-A
MFGDate: 04-29-2013
Serial:504743
DRAM: 1 GiB
PMIC: deviceid=10, revid=11
GSC: v2 0x8a31 0x00
RTC: 0
MMC: FSL_SDHC: 0
SF: Detected W25Q256 with page size 64 KiB, total 32 MiB
No panel detected: default to HDMI
enable_hdmi: setup HDMI monitor
DISP: HDMI (1024x768)
In: serial
Out: serial
Err: serial
RS232: enabled
DIO0: gpio
DIO1: gpio
DIO2: gpio
DIO3: gpio
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
USB device 0: unknown device
** Bad device usb 0 **
MMC: no card present
mmc0(part 0) is current device
MMC: no card present
MMC: no card present
** Bad device mmc 0 **
SF: Detected W25Q256 with page size 64 KiB, total 32 MiB
SF: 2097152 bytes @ 0x90000 Read: OK
Booting from FLASH...
## Loading kernel from FIT Image at 12000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: Linux Kernel OpenWrt Linux-3.8.3
Type: Kernel Image
Compression: uncompressed
Data Start: 0x120000e8
Data Size: 1644616 Bytes = 1.6 MiB
Architecture: ARM
OS: Linux
Load Address: 0x10008000
Entry Point: 0x10008000
Hash algo: crc32
Hash value: 80fbc04b
Hash algo: sha1
Hash value: 41eb2ce27e1e5f2649edce77f673f1e5813bfd4c
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 12000000 ...
Using 'config@1' configuration
Trying 'fdt@1' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x12191a58
Data Size: 23080 Bytes = 22.5 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 271d3e89
Hash algo: sha1
Hash value: b20b952d8ebefe82412e40dad1a647caa2a841d1
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x12191a58
Loading Kernel Image ... OK
Using Device Tree in place at 12191a58, end 1219a47f
Updating MTD partitions...
Adjusting FDT per EEPROM for gw5400-a...
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.8.3 (tharvey@tharvey-desktop) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #3 SMP Tue Apr 9 10:47:30 PDT 2013
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Freescale i.MX6 Quad (Device Tree), model: Gateworks Ventana GW5400
[ 0.000000] Truncating RAM at 10000000-4fffffff to -3f7fffff (vmalloc region overlap).
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c0abb000 s6336 r8192 d14144 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 193040
[ 0.000000] Kernel command line: console=ttymxc1,115200 root=/dev/mtdblock3 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Memory: 760MB = 760MB total
[ 0.000000] Memory: 766308k/766308k available, 11932k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0431e24 (4264 kB)
[ 0.000000] .init : 0xc0432000 - 0xc04668c0 ( 211 kB)
[ 0.000000] .data : 0xc0468000 - 0xc048b5fc ( 142 kB)
[ 0.000000] .bss : 0xc048b5fc - 0xc04ba38c ( 188 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x000000c0, AUX_CTRL 0x02070000, Cache size: 1048576 B
[ 0.000000] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 65075ms
[ 0.000000] CPU identified as i.MX6Q, silicon rev 1.2
[ 0.000198] Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
[ 0.090124] pid_max: default: 32768 minimum: 301
[ 0.090284] Mount-cache hash table entries: 512
[ 0.094900] CPU: Testing write buffer coherency: ok
[ 0.095140] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.095233] Setting up static identity map for 0x10010bf0 - 0x10010c24
[ 0.096531] CPU1: Booted secondary processor
[ 0.185195] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.185937] CPU2: Booted secondary processor
[ 0.225196] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.225940] CPU3: Booted secondary processor
[ 0.265194] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.265238] Brought up 4 CPUs
[ 0.265270] SMP: Total of 4 processors activated (6324.22 BogoMIPS).
[ 0.265967] pinctrl core: initialized pinctrl subsystem
[ 0.266618] regulator-dummy: no parameters
[ 0.267054] NET: Registered protocol family 16
[ 0.269221] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.269696] pwm_init
[ 0.280310] syscon 20c8000.anatop: syscon regmap start 0x20c8000 end 0x20c8fff registered
[ 0.280658] vdd1p1: 800 <--> 1375 mV at 1100 mV
[ 0.281044] vdd3p0: 2800 <--> 3150 mV at 3000 mV
[ 0.281457] vdd2p5: 2000 <--> 2750 mV at 2400 mV
[ 0.281852] cpu: 725 <--> 1450 mV at 1150 mV
[ 0.282241] vddpu: 725 <--> 1450 mV at 1150 mV
[ 0.282648] vddsoc: 725 <--> 1450 mV at 1200 mV
[ 0.284192] syscon 20e0000.iomuxc-gpr: syscon regmap start 0x20e0000 end 0x20e0037 registered
[ 0.289469] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.303320] bio: create slab <bio-0> at 0
[ 0.306766] mxs-dma 110000.dma-apbh: initialized
[ 0.307482] 2P5V: 2500 mV
[ 0.307746] 3P3V: 3300 mV
[ 0.307990] usb_otg_vbus: 5000 mV
[ 0.309008] SCSI subsystem initialized
[ 0.309941] usbcore: registered new interface driver usbfs
[ 0.310086] usbcore: registered new interface driver hub
[ 0.310259] usbcore: registered new device driver usb
[ 0.315962] i2c i2c-0: IMX I2C adapter registered
[ 0.317321] i2c i2c-1: IMX I2C adapter registered
[ 0.319469] i2c i2c-2: IMX I2C adapter registered
[ 0.319619] Linux video capture interface: v2.00
[ 0.319835] pps_core: LinuxPPS API ver. 1 registered
[ 0.319847] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.320810] Advanced Linux Sound Architecture Driver Initialized.
[ 0.322210] Switching to clocksource mxc_timer1
[ 0.324218] NET: Registered protocol family 2
[ 0.324739] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.324875] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.325022] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.325114] TCP: reno registered
[ 0.325131] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.325199] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.325557] NET: Registered protocol family 1
[ 0.325856] i.MXC CPU frequency driver
[ 0.325871] i.MXC CPU frequency driver
[ 0.325881] i.MXC CPU frequency driver
[ 0.325891] i.MXC CPU frequency driver
[ 0.468460] pcie: IMX PCIe port: link up.
[ 0.468707] PCI host bridge to bus 0000:00
[ 0.468730] pci_bus 0000:00: root bus resource [io 0x1000000-0x10fffff]
[ 0.468744] pci_bus 0000:00: root bus resource [mem 0x01100000-0x01efffff]
[ 0.468758] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.469011] PCI: bus0: Fast back to back transfers disabled
[ 0.469026] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.469601] pcie: 1:00.2 0x0000: master abort
[ 0.471113] pcie: 1:00.3 0x0000: master abort
[ 0.472648] pcie: 1:00.4 0x0000: master abort
[ 0.474160] pcie: 1:00.5 0x0000: master abort
[ 0.475670] pcie: 1:00.6 0x0000: master abort
[ 0.477179] pcie: 1:00.7 0x0000: master abort
[ 0.478710] PCI: bus1: Fast back to back transfers disabled
[ 0.478727] pci 0000:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.478834] pcie: 2:00.0 0x0000: master abort
[ 0.480688] pcie: 2:02.0 0x0000: master abort
[ 0.482199] pcie: 2:03.0 0x0000: master abort
[ 0.485748] pcie: 2:10.0 0x0000: master abort
[ 0.487259] pcie: 2:11.0 0x0000: master abort
[ 0.488770] pcie: 2:12.0 0x0000: master abort
[ 0.490279] pcie: 2:13.0 0x0000: master abort
[ 0.491788] pcie: 2:14.0 0x0000: master abort
[ 0.493316] pcie: 2:15.0 0x0000: master abort
[ 0.494828] pcie: 2:16.0 0x0000: master abort
[ 0.496339] pcie: 2:17.0 0x0000: master abort
[ 0.497848] pcie: 2:18.0 0x0000: master abort
[ 0.499357] pcie: 2:19.0 0x0000: master abort
[ 0.500867] pcie: 2:20.0 0x0000: master abort
[ 0.502390] pcie: 2:21.0 0x0000: master abort
[ 0.503900] pcie: 2:22.0 0x0000: master abort
[ 0.505410] pcie: 2:23.0 0x0000: master abort
[ 0.506920] pcie: 2:24.0 0x0000: master abort
[ 0.508430] pcie: 2:25.0 0x0000: master abort
[ 0.509939] pcie: 2:26.0 0x0000: master abort
[ 0.511448] pcie: 2:27.0 0x0000: master abort
[ 0.512971] pcie: 2:28.0 0x0000: master abort
[ 0.514481] pcie: 2:29.0 0x0000: master abort
[ 0.515991] pcie: 2:30.0 0x0000: master abort
[ 0.517500] pcie: 2:31.0 0x0000: master abort
[ 0.519152] PCI: bus2: Fast back to back transfers disabled
[ 0.519168] pci 0000:02:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.519196] pci 0000:02:04.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.519225] pci 0000:02:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.519255] pci 0000:02:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.519283] pci 0000:02:07.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.519310] pci 0000:02:08.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.519337] pci 0000:02:09.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.519503] pcie: 3:00.0 0x0000: master abort
[ 0.521011] PCI: bus3: Fast back to back transfers enabled
[ 0.521187] pcie: 4:00.0 0x0000: master abort
[ 0.522712] PCI: bus4: Fast back to back transfers enabled
[ 0.522893] pcie: 5:00.0 0x0000: master abort
[ 0.524401] PCI: bus5: Fast back to back transfers enabled
[ 0.524573] pcie: 6:00.0 0x0000: master abort
[ 0.526082] PCI: bus6: Fast back to back transfers enabled
[ 0.526255] pcie: 7:00.0 0x0000: master abort
[ 0.527762] PCI: bus7: Fast back to back transfers enabled
[ 0.528439] PCI: bus8: Fast back to back transfers disabled
[ 0.528614] pcie: 9:00.0 0x0000: master abort
[ 0.530123] PCI: bus9: Fast back to back transfers enabled
[ 0.534082] pci 0000:00:00.0: BAR 0: assigned [mem 0x01100000-0x011fffff 64bit pref]
[ 0.534113] pci 0000:00:00.0: BAR 8: assigned [mem 0x01200000-0x013fffff]
[ 0.534127] pci 0000:00:00.0: BAR 6: assigned [mem 0x01400000-0x0140ffff pref]
[ 0.534140] pci 0000:00:00.0: BAR 7: assigned [io 0x1000000-0x1000fff]
[ 0.534158] pci 0000:01:00.0: BAR 8: assigned [mem 0x01200000-0x012fffff]
[ 0.534171] pci 0000:01:00.0: BAR 0: assigned [mem 0x01300000-0x0131ffff]
[ 0.534188] pci 0000:01:00.1: BAR 0: assigned [mem 0x01320000-0x0133ffff]
[ 0.534204] pci 0000:01:00.0: BAR 7: assigned [io 0x1000000-0x1000fff]
[ 0.534223] pci 0000:02:08.0: BAR 8: assigned [mem 0x01200000-0x012fffff]
[ 0.534236] pci 0000:02:08.0: BAR 7: assigned [io 0x1000000-0x1000fff]
[ 0.534249] pci 0000:02:01.0: PCI bridge to [bus 03]
[ 0.534294] pci 0000:02:04.0: PCI bridge to [bus 04]
[ 0.534333] pci 0000:02:05.0: PCI bridge to [bus 05]
[ 0.534371] pci 0000:02:06.0: PCI bridge to [bus 06]
[ 0.534411] pci 0000:02:07.0: PCI bridge to [bus 07]
[ 0.534454] pci 0000:08:00.0: BAR 0: assigned [mem 0x01200000-0x01203fff 64bit]
[ 0.534495] pci 0000:08:00.0: BAR 2: assigned [io 0x1000000-0x10000ff]
[ 0.534513] pci 0000:02:08.0: PCI bridge to [bus 08]
[ 0.534529] pci 0000:02:08.0: bridge window [io 0x1000000-0x1000fff]
[ 0.534549] pci 0000:02:08.0: bridge window [mem 0x01200000-0x012fffff]
[ 0.534579] pci 0000:02:09.0: PCI bridge to [bus 09]
[ 0.534618] pci 0000:01:00.0: PCI bridge to [bus 02-09]
[ 0.534631] pci 0000:01:00.0: bridge window [io 0x1000000-0x1000fff]
[ 0.534648] pci 0000:01:00.0: bridge window [mem 0x01200000-0x012fffff]
[ 0.534670] pci 0000:00:00.0: PCI bridge to [bus 01-09]
[ 0.534682] pci 0000:00:00.0: bridge window [io 0x1000000-0x1000fff]
[ 0.534696] pci 0000:00:00.0: bridge window [mem 0x01200000-0x013fffff]
[ 0.534725] PCI: enabling device 0000:01:00.0 (0140 -> 0143)
[ 0.534748] PCI: enabling device 0000:02:01.0 (0140 -> 0143)
[ 0.534773] PCI: enabling device 0000:02:04.0 (0140 -> 0143)
[ 0.534799] PCI: enabling device 0000:02:05.0 (0140 -> 0143)
[ 0.534824] PCI: enabling device 0000:02:06.0 (0140 -> 0143)
[ 0.534849] PCI: enabling device 0000:02:07.0 (0140 -> 0143)
[ 0.534875] PCI: enabling device 0000:02:08.0 (0140 -> 0143)
[ 0.534900] PCI: enabling device 0000:02:09.0 (0140 -> 0143)
[ 0.546980] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.546998] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.547848] msgmni has been set to 1496
[ 0.548083] io scheduler noop registered
[ 0.548096] io scheduler deadline registered
[ 0.548137] io scheduler cfq registered (default)
[ 0.549129] imx-sdma 20ec000.sdma: loaded firmware 1.1
[ 0.554155] imx-sdma 20ec000.sdma: initialized
[ 0.554559] Serial: IMX driver
[ 0.555082] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
[ 0.555833] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
[ 1.642660] console [ttymxc1] enabled
[ 1.646926] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
[ 1.654387] [drm] Initialized drm 1.1.0 20060810
[ 1.659149] at24 0-0050: 256 byte 24c02 EEPROM, writable, 16 bytes/write
[ 1.665919] at24 0-0051: 256 byte 24c02 EEPROM, writable, 16 bytes/write
[ 1.672679] at24 0-0052: 256 byte 24c02 EEPROM, writable, 16 bytes/write
[ 1.679412] at24 0-0053: 256 byte 24c02 EEPROM, writable, 16 bytes/write
[ 1.688656] spi_imx 2008000.ecspi: master is unqueued, this is deprecated
[ 1.696036] m25p80 spi32766.0: w25q256 (32768 Kbytes)
[ 1.701283] 4 ofpart partitions found on MTD device spi32766.0
[ 1.707159] Creating 4 MTD partitions on "spi32766.0":
[ 1.712322] 0x000000000000-0x000000080000 : "uboot"
[ 1.718256] 0x000000080000-0x000000090000 : "env"
[ 1.723980] 0x000000090000-0x000000290000 : "kernel"
[ 1.729911] 0x000000290000-0x000001000000 : "rootfs"
[ 1.735887] mtd: partition "rootfs" set to be root filesystem
[ 1.741859] mtd: partition "rootfs_data" created automatically, ofs=8D0000, len=730000
[ 1.749905] 0x0000008d0000-0x000001000000 : "rootfs_data"
[ 1.756376] spi_imx 2008000.ecspi: probed
[ 1.775427] libphy: fec_enet_mii_bus: probed
[ 1.780632] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.787197] ehci-pci: EHCI PCI platform driver
[ 1.791815] ehci-platform: EHCI generic platform driver
[ 1.800574] ci_hdrc ci_hdrc.0: can't start gadget role
[ 1.805872] imx_usb 2184200.usb: pinctrl get/select failed, err=-19
[ 1.812526] ci_hdrc ci_hdrc.1: doesn't support gadget
[ 1.817594] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 1.822543] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 1.842279] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 1.848257] hub 1-0:1.0: USB hub found
[ 1.852030] hub 1-0:1.0: 1 port detected
[ 1.856590] input: mma8450 as /devices/virtual/input/input0
[ 1.862750] rtc-ds1672 0-0068: chip found, driver version 0.4
[ 1.869873] rtc-ds1672 0-0068: rtc core: registered rtc-ds1672 as rtc0
[ 1.877356] i2c /dev entries driver
[ 1.881901] imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
[ 1.890463] sdhci: Secure Digital Host Controller Interface driver
[ 1.896669] sdhci: Copyright(c) Pierre Ossman
[ 1.901033] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.908706] mmc0: no vqmmc regulator found
[ 1.952291] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
[ 1.959983] leds-gpio leds.8: pins are not configured from the driver
[ 1.968064] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 1.974711] [drm] No driver support for vblank timestamp query.
[ 1.980641] [drm] Initialized imx-drm 1.0.0 20120507 on minor 0
[ 1.990912] imx-ipuv3 2400000.ipu: DI0 base: 0x02640000 remapped to f00fe000
[ 1.998120] imx-ipuv3 2400000.ipu: DI1 base: 0x02648000 remapped to f0244000
[ 2.005662] imx-ipuv3 2400000.ipu: IPUv3H probed
[ 2.014543] imx-ipuv3 2800000.ipu: DI0 base: 0x02a40000 remapped to f0264000
[ 2.021682] imx-ipuv3 2800000.ipu: DI1 base: 0x02a48000 remapped to f0266000
[ 2.029177] imx-ipuv3 2800000.ipu: IPUv3H probed
[ 2.036438] sgtl5000 2-000a: Failed to get supply 'VDDD': -517
[ 2.042583] 2-000a: 1200 mV normal
[ 2.046278] sgtl5000 2-000a: Using internal LDO instead of VDDD
[ 2.055127] sgtl5000 2-000a: sgtl5000 revision 0x11
[ 2.071211] imx-sgtl5000 sound.13: sgtl5000 <-> 2028000.ssi mapping ok
[ 2.079922] TCP: cubic registered
[ 2.083343] NET: Registered protocol family 17
[ 2.087923] Bridge firewalling registered
[ 2.091948] 8021q: 802.1Q VLAN Support v1.8
[ 2.096250] Registering SWP/SWPB emulation handler
[ 2.103445] rtc-ds1672 0-0068: setting system clock to 1970-01-01 00:00:08 UTC (8)
[ 2.111060] imx-drm imx-drm: No connectors reported connected with modes
[ 2.117793] [drm] Cannot find any crtc or sizes - going 1024x768
[ 2.129631] imx-drm imx-drm: fb0: frame buffer device
[ 2.134816] imx-drm imx-drm: registered panic notifier
[ 2.146669] ALSA device list:
[ 2.149648] #0: imx6q-sabrelite-sgtl5000
[ 2.167097] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.172316] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[ 2.180954] Freeing init memory: 208K
[ 2.404364] hub 1-1:1.0: USB hub found
[ 2.408460] hub 1-1:1.0: 4 ports detected
[ 3.097948] pcie: PCIe abort: address = 0xb6f7d000 fsr = 0x1406 PC = 0xb6f75a48 LR = 0xb6f76578 instr=ef000000
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 7.666174] jffs2: notice: (1165) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 12 of xref (0 dead, 0 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 9.267757] Compat-drivers backport release: compat-drivers-2013-01-21-1
[ 9.274493] Backport based on wireless-testing.git master-2013-02-22
[ 9.280850] compat.git: wireless-testing.git
[ 9.297707] cfg80211: Calling CRDA to update world regulatory domain
[ 9.304178] cfg80211: World regulatory domain updated:
[ 9.309336] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.317569] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.325337] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.333104] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.340855] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.348618] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Failed to set regulatory domain: -7
[ 10.617053] RPC: Registered named UNIX socket transport module.
[ 10.623011] RPC: Registered udp transport module.
[ 10.627719] RPC: Registered tcp transport module.
[ 10.632439] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 10.875585] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 11.239182] PPP generic driver version 2.4.2
[ 11.353666] tun: Universal TUN/TAP device driver, 1.6
[ 11.358732] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 11.419915] gre: GRE over IPv4 demultiplexor driver
[ 11.433469] ip_gre: GRE over IPv4 tunneling driver
[ 11.587444] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 11.742364] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 11.891426] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.022002] NET: Registered protocol family 24
[ 12.146256] nf_conntrack version 0.5.0 (11976 buckets, 47904 max)
[ 12.730875] xt_time: kernel timezone is -0000
[ 12.891681] Ebtables v2.0 registered
[ 13.129050] batman_adv: B.A.T.M.A.N. advanced 2013.1.0 (compatibility version 14) loaded
[ 13.149246] e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k
[ 13.155117] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
[ 13.270863] sky2: driver version 1.30
[ 13.274629] PCI: enabling device 0000:08:00.0 (0140 -> 0143)
[ 13.280417] sky2 0000:08:00.0: Yukon-2 UL 2 chip revision 0
[ 13.286357] arch_setup_msi_irq: 0 of 16
[ 13.382291] sky2 0000:08:00.0: No interrupt generated using MSI, switching to INTx mode.
[ 13.391006] sky2 0000:08:00.0 eth1: addr 00:d0:12:29:ef:6d
[ 13.449598] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 13.513757] uhci_hcd: USB Universal Host Controller Interface driver
[ 13.571457] usbcore: registered new interface driver ath9k_htc
[ 13.677661] usbcore: registered new interface driver cdc_acm
[ 13.683360] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 13.753612] usbcore: registered new interface driver usbserial
[ 13.759528] usbcore: registered new interface driver usbserial_generic
[ 13.766157] usbserial: USB Serial support registered for generic
[ 13.783160] Initializing USB Mass Storage driver...
[ 13.788171] usbcore: registered new interface driver usb-storage
[ 13.794211] USB Mass Storage support registered.
[ 13.856516] usbcore: registered new interface driver ums-alauda
[ 13.871246] usbcore: registered new interface driver ums-cypress
[ 13.885809] usbcore: registered new interface driver ums-datafab
[ 13.900071] usbcore: registered new interface driver ums-freecom
[ 13.914553] usbcore: registered new interface driver ums-isd200
[ 13.928888] usbcore: registered new interface driver ums-jumpshot
[ 13.943433] usbcore: registered new interface driver ums-karma
[ 13.957768] usbcore: registered new interface driver ums-sddr09
[ 13.972145] usbcore: registered new interface driver ums-sddr55
[ 13.986734] usbcore: registered new interface driver ums-usbat
[ 14.030549] usbcore: registered new interface driver asix
[ 14.090829] usbcore: registered new interface driver cdc_ether
[ 14.145884] usbcore: registered new interface driver sierra_net
[ 14.199343] usbcore: registered new interface driver ftdi_sio
[ 14.205205] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 14.265067] usbcore: registered new interface driver pl2303
[ 14.270727] usbserial: USB Serial support registered for pl2303
[ 14.285826] usbcore: registered new interface driver sierra
[ 14.291472] usbserial: USB Serial support registered for Sierra USB modem
[ 14.431176] u32 classifier
[ 14.433921] Performance counters on
[ 14.437762] input device check on
[ 14.441427] Actions configured
[ 14.482749] Mirror/redirect action on
[ 14.553308] usbip_core: module is from the staging directory, the quality is unknown, you have been warned.
[ 14.564541] usbip_core: USB/IP Core v1.0.0
[ 14.577012] vhci_hcd: module is from the staging directory, the quality is unknown, you have been warned.
[ 14.587608] vhci_hcd vhci_hcd: USB/IP Virtual Host Controller
[ 14.593407] vhci_hcd vhci_hcd: new USB bus registered, assigned bus number 2
[ 14.601584] hub 2-0:1.0: USB hub found
[ 14.605434] hub 2-0:1.0: 8 ports detected
[ 14.609725] vhci_hcd: USB/IP 'Virtual' Host Controller (VHCI) Driver v1.0.0
[ 14.625007] usbip_host: module is from the staging directory, the quality is unknown, you have been warned.
[ 14.852596] usbcore: registered new interface driver usbip-host
[ 14.858530] usbip_host: USB/IP Host Driver v1.0.0
[ 17.580699] eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1)
[ 17.590464] device eth0 entered promiscuous mode
[ 19.572619] libphy: 2188000.ethernet:00 - Link is Up - 100/Full
[ 19.578582] br-lan: port 1(eth0) entered forwarding state
[ 19.584053] br-lan: port 1(eth0) entered forwarding state
[ 21.582278] br-lan: port 1(eth0) entered forwarding state
BusyBox v1.19.4 (2013-04-08 22:22:48 PDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r35953)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/#
Note:
See TracWiki
for help on using the wiki.
