Changes between Version 3 and Version 4 of expansion/gw16171


Ignore:
Timestamp:
11/16/2026 09:03:24 PM (85 minutes ago)
Author:
Tim Harvey
Comment:

update antenna section, eventa section, and add anchors for easy linking

Legend:

Unmodified
Added
Removed
Modified
  • expansion/gw16171

    v3 v4  
    44The GW16171 is a precision GNSS M.2 Card featuring the Septentrio mosaic-G5 P6 multi-frequency receiver.
    55
    6 Read more on the official product page here: [https://www.gateworks.com/products/wireless-options/gw16171-septentrio-g5-mosaic-precision-gnss-m2-card/]
     6Read more on the official product page here: [https://www.gateworks.com/products/wireless-options/gw16171-septentrio-g5-mosaic-precision-gnss-m2-card/ GW16171 Precision GNSS M.2 Card]
    77
    88
    … …  
    5151
    5252
     53
     54[=#antennas]
    5355== Antenna
    54 There are two antenna ports for the Mosaic G5. Not all variants support dual antennas however the standard GW16171 with the Mosaic-G5 P6 does.
    55 
    56 To get started, a recommended antenna is the Yokowo Manufacturing of America YOZ-52728ZZ01-YM available [https://www.digikey.com/en/products/detail/yokowo-manufacturing-of-america-llc/YOZ-52728ZZ01-YM/25603978 here]
     56There are two antenna ports for the Mosaic G5. Not all Mosaic-G5 variants support dual antennas however the standard GW16171 with the Mosaic-G5 P6 does:
     57 * ANT1 (Main) is used for postition
     58 * ANT2 (Aux) is used for heading and attitude
     59
     60Note that you can not use ANT2 without ANT1 however in single Antenna mode you can use only ANT1.
     61
     62The Mosaic-G5 defaults to Single Antenna mode. Use the {{{getFrontEndMode}}} and {{{setFrontEndMode}}} receiver commands to get/set the mode however note that once you do this you need to also save the config to boot configuration and reboot the receiver:
     63 * Get Antenna mode:
     64{{{#!bash
     65< getFrontendMode
     66 > $R: getFrontendMode
     67 >   FrontendMode, Nominal
     68}}}
     69  - Nominal mode (default) will choose the best operating mode depending on your product. Normally this is !SingleAnt, but for
     70products with heading as main purpose, this is !DualAnt.
     71 * Set Dual Antenna mode:
     72{{{#!bash
     73setFrontendMode, DualAnt
     74exeCopyConfigFile, Current, Boot
     75exeResetReceiver, Hard, none
     76}}}
     77 * Set Single Antenna mode:
     78{{{#!bash
     79setFrontendMode, SingleAnt
     80exeCopyConfigFile, Current, Boot
     81exeResetReceiver, Hard, none
     82}}}
     83 * Set Nominal (default) Antenna mode:
     84{{{#!bash
     85setFrontendMode, Nominal
     86exeCopyConfigFile, Current, Boot
     87exeResetReceiver, Hard, none
     88}}}
     89
     90
     91
     92A recommended antenna is the Yokowo Manufacturing of America YOZ-52728ZZ01-YM available [https://www.digikey.com/en/products/detail/yokowo-manufacturing-of-america-llc/YOZ-52728ZZ01-YM/25603978 here]
    5793
    5894A smaller option we like is the TW7972, and a bit larger one for machine control-type applications (or car tests) is the !PolaNt* MC.v2.
    … …  
    86122
    87123
     124
     125[=#acm]
    88126=== USB ACM interfaces
    89127The 2x USB ACM interfaces are represented by USB1 and USB2 Connection Descriptors (CD) and would typically enumerate as /dev/ttyACM0 and /dev/ttyACM1.
    … …  
    96134
    97135
     136
     137[=#sd]
    98138== SD Interface
    99139The SD interface on the Mosaic-G5 is a 1-bit SDIO device which goes to a MicroSD socket on the GW16171.
    … …  
    123163
    124164
     165
     166[=#uart]
    125167== UART Interface
    126168The 2-wire UART on the GW16171 is routed to COM1 on the Mosaic-G5.
    … …  
    153195
    154196
     197
     198[=#pps]
    155199== PPS1 Output
    156200The PPS1 output on M.2 pin 34 is highly configurable. The default configuration is to output 1Hz Low2High synchronized with GPS. The PPS output pin routes to the M.2 pin 34 which is UART_RTS for the M.2 E-Key standard.
    … …  
    218262
    219263
     264[=#event]
    220265== EventA Input
    221 The EVENTA input signal on the Moasic-G5 routed to M2 pin 36 on the GW16171 and can be configured to trigger various things.
    222 
    223 When the GW16171 is used on a GW8201 with a GW16FE0 in FSA2 pin 34 is UART_RTS which maps to MX8MP_IOMUXC_ECSPI1_MISO__GPIO5_IO08.
     266The EVENTA input signal on the Moasic-G5 routed to M.2 pin 36 (UART_CTS) on the GW16171 and can be configured to trigger various events.
    224267
    225268Examples:
    226  * Enable the ExtEvent SBF block and send it to COM1 showing the position at the time of the event:
    227 {{{#!bash
    228 < setSBFOutput, Stream1, COM1, ExtEvent+ExtEventPVTGeodetic, OnChange
    229  > $R: setSBFOutput, Stream1, COM1, ExtEvent+ExtEventPVTGeodetic, OnChange
    230  >   SBFOutput, Stream1, COM1, ExtEvent+ExtEventPVTGeodetic, OnChange
    231 }}}
     269 * Configure EventA for a low-to-high transition and send SBF output for !ExtEvent to COM1
     270To configure this via the receiver:
     271{{{#!bash
     272setEventParameters,+EventA,Low2High,0.0 # set polarity/delay for eventa
     273setSBFOutput,Stream1,COM1,ExtEvent,OnChange
     274}}}
     275
     276To view this event for testing you can use the [#rxtools RxControl] tool and go to Tools, Expert Console, ExEvent tab.
     277
     278The Pin mapping for what GPIO is routed to M.2 pin 36 depends greatly on your board and may require device-tree modifications in order to configure it as a GPIO. Here are some examples:
     279 * GW8201 with a GW16FE0 FSA M.2 E-Key adapter in FSA2 pin 34 maps to MX8MP_IOMUXC_ECSPI1_MISO__GPIO5_IO08
     280 * GW9401 with a GW16FE0 FSA M.2 E-Key adapter in FSA2 pin 34 maps to IMX95_PAD_GPIO_IO03__GPIO2_IO_BIT3
     281
    232282
    233283== Receiver
    … …  
    374424
    375425
     426[=#rxtools]
    376427== Using Septentrio !RxTools
    377428Septentrio has a Windows / Linux graphical user interface called [https://www.septentrio.com/en/products/gps-gnss-receiver-software/rxtools RxTools] that can interface with the Mosaic-G5 by redirecting one of its ACM serial ports to a TCP/IP connection.