Changes between Version 20 and Version 21 of malibu/gw3089gblade

Timestamp:

04/17/2023 10:47:05 PM (20 months ago)

Author:

Ron Eisworth

Comment:

--

malibu/gw3089gblade

@@ -36 +36 @@
 
 The JTAG software is under development so for initial programming please see the following link on updating from a TFTP server. 
-* [wiki:malibu/firmware#UpdateFirmwareviaSerialConsoleandEthernetfromBootloader] 
-
-
-
+ * [wiki:malibu/firmware#UpdateFirmwareviaSerialConsoleandEthernetfromBootloader] 
 
 == Ethernet
@@ -50 +47 @@
 [[Image(GW3089ethernet.JPG,300px)]]
 
-===  PoE
-
-Isolated 802.3at 1GbE active PoE is supported on the bottom port. The Gateworks GW10144 802.3at inserter can be used to power individual units and/or during development. See link here for info on GW10144:
+===  Powering Gblade with PoE
+
+Isolated 802.3at 1GbE active PoE is supported on the bottom 1GbE Ethernet port. The Gateworks GW10144 802.3at PoE power supply/inserter can be used to power individual units and/or during development. See link here for info on GW10144:
 [https://tsi.tyconsystems.com/doc/SpecSheets/TP-POE+10G__53V_30W_10GB_PoE_Inserter_Spec_Sheet.pdf Tycon Inserter]
 
-A 802.3at PoE switch is recommended for rackmount applications. 
-
-For 10GbE PoE options, please contact Gateworks Sales.
+For rackmount applications a 802.3at PoE switch is recommended. 
+
+To use the 10GbE port for PoE powering the device, please contact Gateworks Sales.
 
 == NVME Drive
 
-The GBlade needs to be opened up to install a 2280 M-Key NVME flash storage drive. 4 lanes of PCIe is supported.
+The GBlade needs to be opened up to install a 2280 M-Key NVME flash storage drive. The Gblade supports PCIe Gen 3.0 x4 lanes. 
+
+Here are the basic steps to open the case and access the NVME socket. 
+
+ 1. Remove the four frontplate screws using a T8 Torx driver. 
+ 2. Remove the frontplate and move to the side. Note the LED cable does not need to be removed. 
+ 3. Slide out the side plate on the side the LED cable is mounted on. 
+ 4. The M.2 NVME socket should now be visible and a drive can be inserted. Secure the drive to the PEM towards the front of the unit and reinstall the frontplate. 
 
 == LED
@@ -149 +153 @@
  * Operating System (including kernel / rootfs)
 
-An Ubuntu based OS is pre-installed on all Malibu boards before they ship.
-
-Please view the following links for the appropriate software section:
+An Ubuntu based OS is pre-installed on all Malibu boards before they ship. See the following link for the latest pre-built image:
+
+ * [http://dev.gateworks.com/malibu/images/ Pre-built Software Images]
+ * [wiki:malibu/firmware#UpdateFirmwareviaSerialConsoleandEthernetfromBootloader Installation Instructions] 
+
+Additional links available here:
  * [wiki:malibu Main Malibu Wiki Page]
- * [http://dev.gateworks.com/malibu/images/ Pre-built Software Images]
- * [wiki:/malibu/firmware Malibu Software Installation Page]
  * [wiki:malibu/boot Malibu Boot Firmware (up to and including the Bootloader)]
  * [wiki:gsc#GSCVersionHistory GSC Firmware]
@@ -164 +169 @@
 The Linux device tree can often describe a lot about how the hardware is connected, etc.
 
-Link to GW3089/GW8901 Device tree: [https://github.com/Gateworks/linux-malibu/blob/v6.1-malibu/arch/arm64/boot/dts/marvell/cn9130-malibu-gw8901.dts]
+Link to GW3089/GW8901 Device tree: [https://github.com/Gateworks/linux-malibu/blob/v6.1-malibu/arch/arm64/boot/dts/marvell/cn9130-malibu-gw8901.dts Device Tree]
 
 === TPM / Crypto
@@ -181 +186 @@
  -RSA 1024-2048 bit keys
 
+== Enclosure
+
+The GW3089 enclosure uses the following screws for securing the board, fan and frontplate.
+
+ * Frontplate = Torx T8 Head, M3 x 8mm
+ * Fan = Torx T10 Head, M3 x 25mm
+ * Board standoffs = Hex 1.5mm Head M2.5 x 5mm
+
+The fan is a CUI CFM-4020BF-095-342-22 with the following specifications:
+
+ * Operating Voltage: 5VDC
+ * Typical Power Consumption: 1.45W
+ * Typical RPM: 9500 RPM
+ * Typical Noise: 34.2 dBA
+ * MTBF: Typ. 70K Hours @ +40C
+ * Operating Temp: -10C to +70C
+ * Dual Ball Bearing
+ * Auto Restart Protection
+ * Polarity Protection
+ * Soft Start
+ * Tachometer Signal
+ * PWM Control
+ * Safety Approvals: UL, cUL, TUV, CE
+ * RoHS
+
+
 == Wireless