GW3089 GBlade Server Blade

Product Information

All product information and datasheets can be found here: ​https://www.gateworks.com/products/arm-server-blades/gblade-arm-server-blade/

Getting Started

The GBlade is pre-installed with Ubuntu Linux. To power the unit use an 802.3at PoE switch or inserter. The bottom 1GbE RJ45 is the PoE port by default. Contact factory for 10GbE PoE options. Typical power consumption is around 10-13W without any additional cards plugged into the NVME socket.

Serial Console Access

Once the unit is powered, the GBlade serial console can be accessed through the type C USB port through a cable to a desktop/laptop PC. The serial console will show up as a /dev/ttyUSBx device in Linux and can be accessed through a terminal program with the baud rate of 115,200.

Example:

sudo screen /dev/ttyUSB1 115200,cs8

Once connected via the USB cable, SSH can be enabled (it is disabled by default) with instructions here: Enable SSH

Any server software (LAMP stack, etc) can then be installed with the package manager.

apt-get update
apt-get install {your package}

JTAG & Firmware/OS Update

The GW3089 incorporates onboard a USB to JTAG FTDI chip to allow JTAG programming of the unit without the requirement for a separate JTAG dongle (GW16099) which is typically used on other Gateworks SBCs.

The JTAG software is under development so for initial programming please see the following link on updating from a TFTP server.

• malibu/firmware

Ethernet

There are two Ethernet ports, 1GbE (management) and 10GbE (high speed data).

• (eth1) 1GbE RGMII port is on the bottom (PoE by default)
• (eth0) 10GbE XFI port is on the top.

Powering Gblade with PoE

Isolated 802.3at 1GbE active PoE is supported on the bottom 1GbE Ethernet port. The Gateworks GW10144 802.3at PoE power supply/inserter can be used to power individual units and/or during development. See link here for info on GW10144: ​Tycon Inserter

For rackmount applications a 802.3at PoE switch is recommended.

To use the 10GbE port for PoE powering the device, please contact Gateworks Sales.

NVME Drive

The GBlade needs to be opened up to install a 2280 M-Key NVME flash storage drive. The Gblade supports PCIe Gen 3.0 x4 lanes.

Here are the basic steps to open the case and access the NVME socket.

1. Remove the four frontplate screws using a T8 Torx driver.
2. Remove the frontplate and move to the side. Note the LED cable does not need to be removed.
3. Slide out the side plate on the side the LED cable is mounted on.
4. The M.2 NVME socket should now be visible and a drive can be inserted. Secure the drive to the PEM towards the front of the unit and reinstall the frontplate.

LED

A front panel LED is supported.

When power is applied, the LED will be a solid green. The LED will present a green heartbeat pattern is shown once the board is booted into Linux.

LED Programming

To disable the heartbeat LED:

root@jammy-malibu:~# echo none > /sys/class/leds/green\:heartbeat/trigger #disable default green heartbeat
root@jammy-malibu:~# echo 255 > /sys/class/leds/red\:status/brightness #set LED to solid RED

To see more Linux LED examples, see here: linux/led

Thermal & Cooling Fan

The fan runs at specific set points. The trip points are set at 50C, 60C and 80C (as shown in the device tree ​here)

Note also the processor will throttle down if the fan isn't able to achieve proper cooling with the fan.

The GW8901 uses standard Linux cooling-maps, thermal-zones and the pwm-fan driver.

There are several temperature sensors on the board, identified as 'thermal_zones'. These are shown in Linux under /sys/class/thermal:

root@jammy-malibu:~# ls -la /sys/class/thermal/
total 0
drwxr-xr-x  2 root root 0 Jun 27 18:28 .
drwxr-xr-x 62 root root 0 Jun 27 18:28 ..
lrwxrwxrwx  1 root root 0 Jun 27 18:28 cooling_device0 -> ../../devices/virtual/thermal/cooling_device0
lrwxrwxrwx  1 root root 0 Jun 27 18:28 cooling_device1 -> ../../devices/virtual/thermal/cooling_device1
lrwxrwxrwx  1 root root 0 Jun 27 18:31 cooling_device2 -> ../../devices/virtual/thermal/cooling_device2
lrwxrwxrwx  1 root root 0 Jun 27 18:28 thermal_zone0 -> ../../devices/virtual/thermal/thermal_zone0
lrwxrwxrwx  1 root root 0 Jun 27 18:28 thermal_zone1 -> ../../devices/virtual/thermal/thermal_zone1
lrwxrwxrwx  1 root root 0 Jun 27 18:28 thermal_zone2 -> ../../devices/virtual/thermal/thermal_zone2
lrwxrwxrwx  1 root root 0 Jun 27 18:28 thermal_zone3 -> ../../devices/virtual/thermal/thermal_zone3
lrwxrwxrwx  1 root root 0 Jun 27 18:28 thermal_zone4 -> ../../devices/virtual/thermal/thermal_zone4
lrwxrwxrwx  1 root root 0 Jun 27 18:28 thermal_zone5 -> ../../devices/virtual/thermal/thermal_zone5

An example temperature for thermal_zone0 would be 60738, or 60738/1000=60.738 degrees Celsius:

root@jammy-malibu:~# cat /sys/class/thermal/thermal_zone0/temp 
60738

The zones are labeled below. The AP stands for application processor, or the main CPU, with a sensor for each core of the quad core CPU. The CP0 stands for 'co-processor'.

root@jammy-malibu:~# cat /sys/class/thermal/thermal_zone*/type
ap-thermal-ic
ap-thermal-cpu0
ap-thermal-cpu1
ap-thermal-cpu2
ap-thermal-cpu3
cp0-thermal-ic

1U Rack Front Plate

A standard 1U rack front plate is available to install QTY 10 GBlade servers in a rack mount scenario. The 1U plate part number is GW3090. Contact sales@… to purchase.

Gateworks System Controller

The Gateworks System Controller manages things like the real time clock, voltage rails, fan PWM, etc.

More information can be found here: gsc

Software

The GW3089 is part of the Gateworks Malibu family of SBCs.

Malibu Software is comprised of many pieces, including the following:

• GSC (Gateworks System Controller) Firmware
• Boot Firmware (ARM Trusted Firmware, DDR controller Firmware, U-Boot Bootloader)
• Operating System (including kernel / rootfs)

An Ubuntu based OS is pre-installed on all Malibu boards before they ship. See the following link for the latest pre-built image:

• ​Pre-built Software Images
• Installation Instructions

Additional links available here:

• Main Malibu Wiki Page
• Malibu Boot Firmware (up to and including the Bootloader)
• GSC Firmware
• Main Ubuntu Page
• Webmin Installation Page

Device Tree

The Linux device tree can often describe a lot about how the hardware is connected, etc.

Link to GW3089/GW8901 Device tree: ​Device Tree

TPM / Crypto

On the board is a Microchip ATTPM20P-H6MA1-10

This is compliant to the Trusted Computing Group (TCG) Trusted Platform Module (TPM) Version 2.0, r116 Trusted Platform Module Library

Cryptographic Support for:

• HMAC
• AES-128
• SHA-1
• SHA-256
• ECC BN_P256, ECCNIST_P256 -RSA 1024-2048 bit keys

Enclosure

The GW3089 enclosure uses the following screws for securing the board, fan and frontplate.

• Frontplate = Torx T8 Head, M3 x 8mm
• Fan = Torx T10 Head, M3 x 25mm
• Board standoffs = Hex 1.5mm Head M2.5 x 5mm

The fan is a CUI CFM-4020BF-095-342-22 with the following specifications:

• Operating Voltage: 5VDC
• Typical Power Consumption: 1.45W
• Typical RPM: 9500 RPM
• Typical Noise: 34.2 dBA
• MTBF: Typ. 70K Hours @ +40C
• Operating Temp: -10C to +70C
• Dual Ball Bearing
• Auto Restart Protection
• Polarity Protection
• Soft Start
• Tachometer Signal
• PWM Control
• Safety Approvals: UL, cUL, TUV, CE
• RoHS

Wireless

Wireless was not intended for this ethernet connected blade server.