wiki:alternateconnectors

Version 31 (modified by Ryan Erbstoesser, 10 months ago) ( diff )

remove 5100/6100 ethernet section

  1. Connector and Cable Information
    1. Power Connectors
      1. 0.156"/3.96mm Pitch
      2. 0.079" (2.00mm) Pitch
      3. Locking Barrel Jack
    2. Ethernet Connectors
        1. !Venice Alternate Ethernet Diagram
    3. HDMI Connector
    4. USB Connectors
    5. Pushbutton - Switch Connector
    6. Front Panel LED ( Red / Green)
    7. JTAG / 2x5 10 Pin Connectors
    8. Peripheral Adapters
  2. Cable Connector Information
    1. JST 1x2 (2mm spacing)
    2. JST 1x3 (2mm spacing)
    3. JST 1x4 (2mm spacing)
    4. JST 1x5 (2mm spacing)
    5. JST 1x6 (2mm spacing)
    6. JST 1x10 (2mm spacing)
  3. GW6100 / GW5913 / GW7100 20-pin Connector
  4. GW5510 30-pin Connector
  5. GW5100 and GW5520 Peripheral Connectors / 2x5 10 Pin Connectors
  6. GW16112 USB Expansion Board Connector Information
  7. GW16113 Expansion Card Cable Information
  8. SMA and RPSMA Antenna and Cables
  9. Mini-PCIe Connector Specification

Connector and Cable Information

Gateworks provides alternate connectors for specific items on the SBC. These alternate connectors are typically used for rugged applications where a more flat profile or locking connector is needed.

Power Connectors

Gateworks typically loads a 2.5mm barrel jack connector for power however most boards include alternate holes for 0.156"/3.96mm spaced power connectors on larger boards and 2mm pitched connectors on smaller boards. Here is a list of common connectors that Gateworks stocks. Contact support for more information on having your board loaded with one of these alternate connectors.

0.156"/3.96mm Pitch

  • Molex Vertical (locking, non-shrouded)-GW#02050506: (most common)
    • Pitch - 0.156" (3.96mm)
    • Common on larger boards, such as Ventana GW53xx, 54xx, 63xx, 64xx
    • ​Digi-Key
  • AMP/Tyco Horizontal (locking, non-shrouded)-GW#02050194:
  • JST Vertical (locking, shrouded)-GW#02050561:
  • JST Horizontal (locking, non-shrouded)-GW#02050680:

0.079" (2.00mm) Pitch

  • Common on smaller boards like the GW5100, GW5530, GW6100

Locking Barrel Jack

  • Gateworks offers a cable with this connector for boards such as the GW5100. The cable features a 2-pin JST (2mm pitch) on one side which terminates to the screw locking barrel jack. See the following link and picture: (​GW10132). This can be used on boards with 2-pin JST power connectors such as the GW5100.

Ethernet Connectors

Ethernet requires 8 pins for gigabit and 4 pins for 10/100.

We typically use a 2x4 connector with 2mm spacing and through-hole. This can be done on all Venice SBCs, including the GW71xx.

  • JST 8 pin right angle- Shrouded GW PN 02050686
    • S08B-PUDSS-1(LF)(SN)
    • Digi-Key Part Number: 455-2485-ND ​Link Here
  • JST 8 pin vertical - Shrouded GW PN 02050649
    • B08B-PUDSS-1(LF)(SN)
    • Digi-Key Part Number: 455-2499-ND ​Link Here
    • Samtec 8 pin right angle header - Shrouded GW#02050737
      • T2M-104-01-L-D-RA-WT

!Venice Alternate Ethernet Diagram

HDMI Connector

There are no options for headers for the HDMI port on the Ventana.

USB Connectors

USB is typically 8 pins and SMT.

  • USB Host - 8 pin Vertical Shrouded 2x4x2MM
  • USB OTG (Ventana) - Vertical Latching - 1X4X1.25MM
    • Hirose DF13-4P-1.25DSA
    • GW 02050699
    • 1X4X1.25MM
    • Ventana Note:
      • Boards require resistor load for host or peripheral mode
      • On boards that do not have an OTG_ID pin to dictate host vs periperhal mode you can assign the role via dt or runtime. See wiki:linux/OTG#dual-role

Pushbutton - Switch Connector

The standard pushbutton on most boards can be replaced with a header typically:

Front Panel LED ( Red / Green)

The standard LED on most boards can be replaced with a header typically that is .1 inch or 2.54mm and a 1x2.

JTAG / 2x5 10 Pin Connectors

This is a 10 pin small header. (2X5X0.05IN,1.75A,HEADER)

Cables are available for purchase here: ​http://shop.gateworks.com/index.php?route=product/product&path=70_80&product_id=24

Cables made use: Samtec FFSD-05-D-03.00-01-N

The connector on the board itself: Samtec FTSH-105-01-L-DV-K-A

Peripheral Adapters

Cable Connector Information

The Ventana, Newport, and Venice boards use a variety of JST 2mm spacing connectors for the different I/O ports (RS232, CAN, DIO, video, analog, tamper, etc.). Mates to these connectors can be purchased at Digikey. Here is the info for the various connectors:

JST 1x2 (2mm spacing)

Gateworks Online Shop 2 pin to bare leads:

Gateworks Online Shop 2 pin to 2 pin:

Onboard Connector

Mate Connector Housing

Mate Crimps (note – see associated products under the connector housing for other crimp options)

JST 1x3 (2mm spacing)

Gateworks Online Shop 3 pin to bare leads:

Onboard Connector

Mate Connector Housing

Mate Crimps (note – see associated products under the connector housing for other crimp options)

JST 1x4 (2mm spacing)

Please see DigiKey and User Manual.

Gateworks Online Shop 4 pin to RJ45 (could be cut)

JST 1x5 (2mm spacing)

Gateworks Online Shop 5 pin to bare leads

Gateworks Online Shop 5 pin to 5pin

Onboard Connector

Mate Connector Housing

Mate Crimps (note – see associated products under the connector housing for other crimp options)

JST 1x6 (2mm spacing)

Often used for SPI, a 6-pin header in a 1x6 configuration with 2mm spacing.

Gateworks accessory cable: ​Gateworks Shop

Onboard Connector

  • JST B06B-PASK-1(LF)(SN)

Mate Connector Housing

  • The mating connector is a JST PAP-06V-S, available from Digi-Key as part number 455-1490-ND.

Mate Crimps (note – see associated products under the connector housing for other crimp options)

  • The mating connector pins are JST SPHD-002T-P05, available from Digi-Key as part number 455-1313-1-ND.

JST 1x10 (2mm spacing)

Often used for DIO, a 10-pin header in a 1x10 configuration with 2mm spacing.

Onboard Connector

  • JST B10B-PASK-1(LF)(SN)

Mate Connector Housing

  • The mating connector is a JST PAP-10V-S, available from Digi-Key as part number

455-1494-ND. ​https://www.digikey.com/en/products/detail/jst-sales-america-inc/PAP-10V-S/759982

Mate Crimps (note – see associated products under the connector housing for other crimp options)

  • The mating connector pins are JST SPHD-002T-P05, available from Digi-Key as part number 455-1313-1-ND.

GW6100 / GW5913 / GW7100 20-pin Connector

A 20-pin expansion header for access to the I/O signals. This is a 2x10 Connector with 1.25MM pitch. The connector on the board is JST S20B-J11DK.

The mating connector would be a JST GHDR-20V-S(F).

Gateworks sells a development cable GW10127 here: ​https://shop.gateworks.com/index.php?route=product/product&product_id=214&search=GW10127

GW5510 30-pin Connector

The GW5510/GW5514 uses a 30-pin expansion header for access to the I/O signals. A Samtec TFM-115-22-L-D-A-TR connector is used on the board for this header. Samtec has both board to board and board to cable options for this connector. For board to board the mating board should use a Samtec SFM-115-02-L-D-A-TR or SFSD-15-28-G-03.25-S. See the GW16111 Expansion board as an example break out board for the GW5510: ​http://www.gateworks.com/product/item/ventana-gw16111-expansion-adapter

For board to cable options the Samtec SFSD series can be used. Pins are rated up to 2.9A per pin.

There is no single direct part number because the wiring gauge will differ for each customer, etc. There are many options.

Document from Samtec:

Samples may be available on the following link here: ​https://www.samtec.com/technical-specifications/default.aspx?seriesMaster=SFSD

Example Digikey link: ​http://www.digikey.com/product-search/en?k=sfsd-15&mnonly=0&newproducts=0&ColumnSort=-1000011&page=1&stock=0&pbfree=0&rohs=0&quantity=&ptm=0&fid=0&pageSize=25

GW5100 and GW5520 Peripheral Connectors / 2x5 10 Pin Connectors

This is a 10 pin small header. (2X5X0.05IN,1.75A,HEADER)

Cables are available for purchase here: ​http://shop.gateworks.com/index.php?route=product/product&path=70_80&product_id=24

Cables made use: Samtec FFSD-05-D-03.00-01-N

The connector on the board itself: Samtec FTSH-105-01-L-DV-K-A

GW16112 USB Expansion Board Connector Information

Gateworks sells an accessory cable pre-made here: ​GW10102 USB Cable

The connector on our board is:

CONT,90DEG,MICRO-LOCK,1X4X1.25MM,SHRD

Molex 504195-0470

​http://www.digikey.com/product-search/en?lang=en&site=US&WT.z_homepage_link=hp_go_button&KeyWords=504195-0470

The mating connector on digi-key is being shown as: Molex 504193-0400

​http://www.digikey.com/product-detail/en/5041930400/WM10575-ND/4879321

GW16113 Expansion Card Cable Information

The GW16113 is a Mini-PCIe I/O Card. Gateworks has produced a pre-made cable, GW10103.

There are 3 connectors on the card for signalling, all connectors are the same.

Connector Shell

  • Molex 504193-1000

Connector Terminals

  • Molex 504185-1000

SMA and RPSMA Antenna and Cables

Gateworks offers a number of cables along with WiFi, Cellular and GPS antenna for use with our products. The following chart provides a quick reference for the various SMA/RPSMA Male/Female connector configurations. The table also provides Gateworks part numbers for products that use these connectors in our online shop ​located here

SMA and RPSMA Chart for Antenna and Cables

Mini-PCIe Connector Specification

See the following link for information on the Mini-PCIe connector used on Gateworks SBCs. Link

Attachments (13)

Download all attachments as: .zip

Note: See TracWiki for help on using the wiki.