wiki:venice/firmware

Version 13 (modified by Tim Harvey, 18 months ago) ( diff )

update pre-built image section

  1. Updating Venice Firmware / Software
  2. Pre-Built Images
  3. Firmware Versioning
  4. Updating Firmware
    1. JTAG Programming
    2. Update Firmware via Serial Console and Ethernet from Bootloader
        1. Update Entire Firmware (recommended)
        2. Updating just the boot firmware
        3. Updating just the root filesystem
      2. TFTP Error Troubleshooting
  5. Updating GSC firmware
      1. Update GSC Firmware via JTAG

Updating Venice Firmware / Software

This page is all about updating / flashing firmware / software onto a Venice SBC.

The various components of the 'firmware' on a Venice board which you may want to update from time to time are (lowest level components listed first):

  • GSC firmware
  • SPL
  • Linux device-tree
  • U-Boot bootloader
  • Linux kernel
  • root filesystem

Some components above you can update individually in Linux using dd or in U-Boot using mmc write taking care to place them at the right offset.

Pre-Built Images

Various Pre-built images can be found on ​http://dev.gateworks.com/venice including:

Gateworks System Controller files are 'board specific' meaning the file used depends on the baseboard or SOM model. Boot firmware images are 'SOC specific' meaning there is a specific one to match the SOC on your board - IMX8M Mini (imx8mm) vs IMX8M Nano (imx8mn) vs IMX8M Plus (imx8mp). Compressed Disk Images are written to the eMMC user partition which contains a disk partition table and the various OS partitions (assuming the boot firmware is booting from emmc boot0 or boot1 hardware partition).

Firmware Versioning

You can determine the firmware version of various portions of the firmware by looking for banners on the serial console. For example: 

U-Boot SPL 2020.04-g0a0109fcfb (Oct 07 2020 - 19:30:09 +0000)
GSC     : v57 0x4d20 RST:VIN Thermal Protection Enabled
Model   : GW7301-00-B1B
...
U-Boot 2020.04-g0a0109fcfb (Oct 07 2020 - 19:30:09 +0000), Build: jenkins-venice-bsp-24
...
[    0.000000] Linux version 5.4.45-g43e409dc8906 (jenkins@bionic_builder) (gcc version 8.4.0 (Buildroot 2020.05.2-109-g32cec2af36)) #1 SMP Wed Oct 7 18:43:20 UTC 2020
...
Ubuntu 20.04.1 LTS focal-venice ttymxc1

Gateworks-Ubuntu-gateworks-g65dac90 Tue Oct  6 23:54:49 UTC 2020
...

The above output shows you:

  • Secondary Program Loader (SPL) GIT revision and build date
  • GSC firmware version
  • U-Boot GIT revision and build date
  • Linux kernel version, GIT revision, build date and build source
  • Ubuntu root filesystem version and GIT revision of the Gateworks ​ubuntu-rootfs.sh that created it (use dpkg -l | grep "^ii" to see what packages and versions are installed

Updating Firmware

This section provides instructions for updating both GSC firmware as well as boot device firmware.

There are two methods for updating firmware:

  • on a live board using Serial Console and Ethernet
  • using a GW16099 JTAG dongle (see below)

The various items that can be easily updated:

  • GSC Firmware - Can be updated via JTAG or at runtime - see below)
  • Boot Firmware (Everything up to and including the Bootloader)
  • Root Filesystem (Operating System)

JTAG Programming

The Gateworks JTAG adapter (GW16099) is available in the Venice Dev Kit as well as on the Gateworks web store ​here

All Venice boards have a 10-pin JTAG header which provides:

  • JTAG Programming for embedded emmc flash - see here for instructions
  • Serial Console access via UART2 (/dev/ttymxc1)

Please Note:

  • Only flash .bin files via the JTAG programmer and jtag_usbv4
  • Linux software is supported for programming Venice (jtag_usbv4 required). Windows is not supported. (Serial console through Windows does work).
  • JTAG Programming of eMMC is supported by ​jtag_usbv4 - see here. Due to this being a slow process for large eMMC devices it is recommended to program boot firmware via JTAG if you brick your board and use the bootloader to install firmware when possible for speed (see #serial-ethernet below).
  • JTAG Programming of the GSC firmware is supported by ​jtag_usbv4 - see below

To flash the Venice boot firmware (no operating system), use the following command: 

sudo ./jtag_usbv4 –p firmware-venice-imx8mm.bin

Update Firmware via Serial Console and Ethernet from Bootloader

The quickest and easiest way to update your firmware is via Serial Console and Ethernet. You can do this either in the U-Boot bootloader (recommended) or within a Linux OS.

If updating firmware via Bootloader/Serial/Ethernet (recommended for speed) you need to setup a TFTP server to host the files for transfer. Alternatively you could load firmware files from removable storage (microSD, or USB Mass Storage for example) however you will need to deviate from the examples below. For details on setting up a TFTP server see here.

The following instructions assume your board target IP address is 192.168.1.1 and you have a TFTP server at 192.168.1.146. Adjust environment according to your network via 'setenv ipaddr <ipaddr>' and 'setenv serverip <serverip>'.

The methods you use to update the firmware depends on what specifically you are trying to update.

Be care to use firmware images built for the specific SOC on the board you are using. Venice boards use a variety of IMX8M SoC's which have different boot firmware:

Board SoC Notes
GW710x-0x-* i.MX8M Mini (aka IMX8MM) use firmware with 'imx8mm' in the name
GW720x-0x-* i.MX8M Mini (aka IMX8MM) use firmware with 'imx8mm' in the name
GW730x-0x-* i.MX8M Mini (aka IMX8MM) use firmware with 'imx8mm' in the name
GW740x-* i.MX8M Plus (aka IMX8MP) use firmware with 'imx8mp' in the name

You can tell what you are using by watching the board boot: 

U-Boot 2022.07-g1050480603 (Aug 19 2022 - 17:02:47 +0000), Build: jenkins-venice-bsp-122

CPU:   Freescale i.MX8MP[8] rev1.1 1600 MHz (running at 1200 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 28C
...
Hit any key to stop autoboot:  0 
u-boot=> print soc
soc=imx8mp
  • The above CPU banner shows 'i.MX8MP' which requires firmware with a 'imx8mp' in its name
  • The latest firmware images set the 'soc' U-Boot env variable to match the SoC you are using

Update Entire Firmware (recommended)

Update the entire device from a Compressed Disk Image. This image includes the partition table, boot firmware, bootloader environment, as well as entire OS and kernel:

Complete Compressed Disk Images are available for download here: ​http://dev.gateworks.com/venice/images/

  • Be sure to use one that is compatible with the SoC on your board

Procedure:

  • Via U-Boot: 
    #First, setup the IP and server IP as described above (example IPs below)
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.2 
# setup network environment (use bootp or static by setting ipaddr/serverip and optional netmask/gatewayip)
setenv autoload 0; bootp  # use dhcp for network config but do not fetch a file
# choose the device to update
setenv dev 2 # sets MMC device to be flashed - see mmc list
# set your image
setenv image <distro>-venice-<soc>.img.gz
# update
run update_all
    • This is what the update_all script does if your curious: 
      update_all=tftpboot ${loadaddr} ${image} && gzwrite mmc ${dev} ${loadaddr} ${filesize}
  • Via Linux (when the volume is unmounted): 
    # fetch your file
cd /tmp
wget http://dev.gateworks.com/venice/images/<distro>-venice-<soc>.img.gz
# uncompress and write to the emmc device
zcat <disro>-venice-<soc>.img.gz | dd of=/dev/mmcblk0 bs=4M

Updating just the boot firmware

Updating the Boot firmware via this method includes the SPL, U-Boot, the device-tree, and the ATF. The method here specifically does not update the disk partition table at the beginning of the boot device as that really has nothing to do with the boot firmware. This method also does not destroy any current U-Boot environment.

Note that the IMX8 BOOT ROM fetches code starting at a 33K offset (in order to reserve everything below that for things like disk partition tables).

The latest pre-built Bootloader images for Venice are available for download here: ​http://dev.gateworks.com/venice/boot_firmware/

  • Be sure to use one that is compatible with the SoC on your board

Procedure:

  • Via U-Boot:
    • for IMX8M Mini board variants: 
      # setup network environment (use bootp or static by setting ipaddr/serverip and optional netmask/gatewayip)
bootp  # optional: use dhcp for network config
# choose the device to update
setenv dev 2 # sets MMC device to be flashed - see mmc list
# set your image
setenv image venice-$soc-flash.bin # with any tftp server directories in front of the filename
# update
run update_firmware
      • This is what the update_firmware script does if your curious: 
        update_firmware=tftpboot $loadaddr $image && setexpr blkcnt $filesize + 0x1ff && setexpr blkcnt $blkcnt / 0x200 && mmc dev $dev && mmc write $loadaddr 0x42 $blkcnt
    • for IMX8M Nano board variants: 
      # setup network environment (use bootp or static by setting ipaddr/serverip and optional netmask/gatewayip)
setenv autoload 0; bootp  # use dhcp for network config but do not fetch a file
# choose the device to update
setenv dev 2 # sets MMC device to be flashed - see mmc list
# set your image
setenv image venice-$soc-flash.bin # with any tftp server directories in front of the filename
# update
run update_firmware
      • This is what the update_firmware script does if your curious: 
        update_firmware=tftpboot $loadaddr $image && setexpr blkcnt $filesize + 0x1ff && setexpr blkcnt $blkcnt / 0x200 && mmc dev $dev && mmc write $loadaddr $splblk $blkcnt
  • Via Linux:
    • Updating via Linux requires you to download the 'venice-<soc>-flash.bin' file (pre-built images can be found ​here and to use the correct offset in the boot device which varies per SoC:
    • for IMX8M Mini board variants: 
      # fetch your file
cd /tmp
wget http://dev.gateworks.com/venice/boot_firmware/venice-imx8mm-flash.bin
# uncompress and write to the emmc device to 33K offset
dd if=venice-imx8mm-flash.bin of=/dev/mmcblk2 bs=1K seek=33
    • for IMX8M Nano board variants: 
      # fetch your file
cd /tmp
wget http://dev.gateworks.com/venice/boot_firmware/venice-imx8mn-flash.bin
# uncompress and write to the emmc device to 32K offset
dd if=venice-imx8mn-flash.bin of=/dev/mmcblk2 bs=1K seek=32
    • for IMX8M Plus board variants: 
      # fetch your file
cd /tmp
wget http://dev.gateworks.com/venice/boot_firmware/venice-imx8mp-flash.bin
# uncompress and write to the emmc device to 32K offset
dd if=venice-imx8mp-flash.bin of=/dev/mmcblk2 bs=1K seek=32

Updating just the root filesystem

Updating the root filesystem from a 'compressed filesystem image' is easily done in U-Boot or Linux.

Note that Gateworks does not host any pre-built filesystem images on our servers but the Venice BSP builds one for you from a downloaded rootfs tarball when you build the ubuntu-image target. The file is in the bsp directory as focal-venice.ext4 and can be compressed with gzip focal-venice.ext4

Procedure:

  • Via U-Boot: 
    # setup network environment (use bootp or static by setting ipaddr/serverip and optional netmask/gatewayip)
setenv autoload 0; bootp  # use dhcp for network config but do not fetch a file
# choose the device to update
setenv dev 2 # sets MMC device to be flashed - see mmc list
# set your image
setenv image rootfs.ext4.gz # with any tftp server directories in front of the filename
# update
run update_rootfs
    • This is what the update_rootfs script does if your curious: 
      update_rootfs=tftpboot $loadaddr $image && gzwrite mmc $dev $loadaddr $filesize 100000 1000000
    • Note gzwrite is used so the filesystem image must be compressed with 'gzip' (otherwise you could use mmc write manually). The data (ie type of filesystem or content ) does not matter here
    • Note the flash offset is 0x1000000 blocks which is 16MiB
    • Note the dev and image env variables are used by this script
  • Via Linux: 
    # fetch your file
cd /tmp
wget http://sever/rootfs.ext4.gz
# uncompress and write to the emmc device to 16M offset
dd if=venice-imx8mm-flash.bin of=/dev/mmcblk0 bs=1M seek=16

TFTP Error Troubleshooting

There are many reasons why TFTP may fail including:

  • firewall issue keeping your TFTP server for being accessible (make sure you can ping it!)
  • invalid network configuration (netmask, gatewayip, ipaddr, serverip) - again make sure you can ping it!
  • 'TFTP error: trying to overwrite reserved memory...' - indicates you are trying to transfer a file that is larger than system memory. You will need to split the file into chunks and flash them individually at the right offsets

Updating GSC firmware

The GSC firmware is updated via the gsc_update application running under Linux as described at on the gsc wiki. While it takes only a few seconds to update there is no recovery for a failed update. Gateworks has ensured that this update is robust but can not survive a power-cut or kernel crash in the middle of the update. Updates to the GSC firmware are expected to be rare.

Update GSC Firmware via JTAG

To update the GSC firmware via JTAG download the jtag_usbv4 application on a Linux x86 host from ​here and execute as follows: 

./jtag_usbv4 -m gsc_7000_v57.txt

Note that the ftdi_sio kernel module must not be loaded (sudo rmmod ftdi_sio) and you may need to run this command as root by pre-pending a sudo depending on the configuration of your linux host.

For more details please see:

Note: See TracWiki for help on using the wiki.