wiki:gettingstarted

Version 5 (modified by Tim Harvey, 6 years ago) ( diff )

remove avila/cambria/rincon data

  1. Getting Started with a Gateworks SBC
  2. Required items
  3. Physical Connections
    1. Power
    2. Communication
  4. First Steps
  5. Next Steps
  6. Software Update
    1. Installing Firmware

Getting Started with a Gateworks SBC

Welcome! Thank you for purchasing a Gateworks single board computer (SBC). We hope to get you started with a little bit of info from our Gateworks wiki site.

Gateworks single board computers (SBC) are powerful, low power network processor boards that are unlimited in their capabilities. Typically, you will find OpenWrt (Linux) pre-installed by default, and thus a lot of information is devoted towards configuring and using the OpenWRT software. Because OpenWrt is open source, Gateworks encourages customers to also leverage the open source community of ​OpenWrt on the web! The Ventana & Newport family also supports other BSPs that can be found on the Ventana Product Wiki Page & Newport Product Wiki Page.

We highly encourage you to utilize this wiki (How to Use Gateworks Wiki) after getting your single board computer turned on with the step by step instructions below.

Required items

To get started and get connected to your board you will need:

  1. Gateworks Single Board Computer
  2. Power supply (there are many options here, please use the supply sent with the development kit to get started)
  3. JTAG USB Programmer - not required but VERY helpful. Used for programming board and serial console access. (Included in development kit) More info on JTAG here
  4. A computer, preferably a Linux machine such as Ubuntu. Windows will also work.
  5. Operating Manuals are also available online at ​http://www.gateworks.com/usermanuals which contain very helpful information.

Physical Connections

There are two main connections to the single board computer ( SBC ).

  1. Power
  2. Communication

Power

  • Most Gateworks' boards support voltages between 10VDC - 48VDC. Please consult the operating manual.
  • If a development kit was purchased, a 12V or 24V DC Wall supply is included that will connect to the power connector barrel jack on the GateworksSBC.
  • Some boards require a 2 pin specialty connector. Silkscreen labels are often labeled VIN for voltage input.
  • POE is possible on certain models. 802.3af is available on certain models. Passive POE between 10-48VDC is often supported. Please consult the user manual. POE Information

Communication

USB JTAG Dongle (included with development kits, or sold separately ​Buy a Jtag - This device is necessary for serial console access.

Example Configuration:

First Steps

Steps to get to a command prompt on the board:

  1. Serial Console.
  2. Connect: the communication cables, such as the JTAG cable or an ethernet cable or serial cable.
  3. Start console program (configured in step 1.)
  4. Connect power.
  5. The board will start outputting text out of the serial console.
    • Yocto OS Login: root
    • See example picture below:

Next Steps

Now that you can login to the board, the options are unlimited! Start using the Gateworks board for your intended use!

There is lots of great information on the Gateworks Software Wiki homepage pointing to many examples, hints, tips, and tricks!

Please use the search box in the top right hand corner as well! Product Manuals are also available online at ​http://www.gateworks.com/usermanuals which contain very helpful information.

Recommended reading:

Feel free to contact us for any support at support@gateworks.com

Software Update

The Gateworks SBC is shipped with software pre-installed. However, software is continually being enhanced and improved. Gateworks recommends reviewing the latest versions compared to what is already installed and updating accordingly.

Installing Firmware

Gateworks Boards are shipped with a default firmware pre-installed, but if you want a specific BSP or version, or want to ensure you have the latest firmware you can update it in a couple different ways:

  1. Software - Firmware image - (Note: Your board comes with the firmware pre-installed, so you may be able to skip this step. ), typically OpenWRT, the Linux distribution that Gateworks runs on the SBC (single board computers) OpenWrt- either download a pre-built binary from our website, or compile your own (Linux only).
    1. Pre-built binaries can be found on each family's respective page: ​See here
    2. Building / Compiling firmware:

Attachments (6)

Download all attachments as: .zip

Note: See TracWiki for help on using the wiki.